Read Panasonic VL-GD001RU Service Manual online
14 EEPROM LAYOUT
14.1. Scope
The purpose of this section is to describe the layout of the EEPROM (IC8) for the VL-GD001RU.
The EEPROM contains hardware, software, and user specific parameters. Some parameters are set during production of the
handset, some are set by the user when configuring the handset, and some during normal use of the phone.
handset, some are set by the user when configuring the handset, and some during normal use of the phone.
14.2. Introduction
The handset uses EEPROM (IC8) for storing volatile parameters. All parameters are set up before the handset the factory.
Some of these are vital for the operation of the hardware so a set of default parameters is programmed before the actual
hardware fine-tuning can be initiated. This document lists all default settings with a short description.
Some of these are vital for the operation of the hardware so a set of default parameters is programmed before the actual
hardware fine-tuning can be initiated. This document lists all default settings with a short description.
This document lists all default parameters with a short description.
Initial Type
Description
F
The data initialized by only F command
0
The data initialized by F and 0 command
1
The data initialized by F, 0 and 1 command
2
The data initialized by F, 0, 1 and 2 command
3
The data initialized by all command (F, 0, 1, 2, 3)
Country Setting
Description
x
Default - no specific country setting, so revert to default value.
14.3. EEPROM contents
Address
Initial
Type
Name
Description
Default value
Country
Setting
0001
F
EEP_FreqTrim_L
Setting value of FREQ_TRIM_REG
0x75
x
0002
F
EEP_BandGap
Setting value of BandGap REG
0x08
x
0003
F
EEP_Rf_Modulation
Setting value of RF modulation
0x0C
x
0008
F
EEP_RssiComp1
Offset to be subtracted from ADC- value.
Measured RSSI at -81 dBm (0-0x3f)
Measured RSSI at -81 dBm (0-0x3f)
0x22
x
0009
F
EEP_RssiComp2
Offset to be subtracted from ADC- value.
Measured RSSI at -63 dBm (0-0x3f)
Measured RSSI at -63 dBm (0-0x3f)
0x2A
x
0010
-
EEP_Ipei
International Portable Part Equipment Identities.
A concatenation of an EMC and a unique 20 bit Serial
Number.
A concatenation of an EMC and a unique 20 bit Serial
Number.
0x00,0x00,0x00,
0x00,0x00
x
001D
0
EEP_HandsetNumber
HandsetNumber of Subscription0.
0xFF,0xFF
x
001F
0
EEP_HandsetNumber1
HandsetNumber of Subscription1.
0xFF,0xFF
x
0021
0
EEP_HandsetNumber2
HandsetNumber of Subscription2.
0xFF,0xFF
x
0023
0
EEP_HandsetNumber3
HandsetNumber of Subscription3.
0xFF,0xFF
x
0025
0
EEP_Subscription0
GAP Subscription Data. Storage for 4 subscriptions each
with 53 bytes.
<Subscription>
020: SUB_boAssignedIPUI
021: SUB_abIPUI[14]
02F: SUB_abPARK[5]
034: SUB_abSARI[4]
038: SUB_bPLI
039: SUB_bLAL
03A: SUB_abARIplusRPN[5]
03F: SUB_boZAP
040: SUB_bZAP
041: SUB_boServiceClass
042: SUB_bServiceClass
043: AK_boUAKavailable
044: AK_boUAKproven
045: AK_abUAK_or_AC [16]
with 53 bytes.
<Subscription>
020: SUB_boAssignedIPUI
021: SUB_abIPUI[14]
02F: SUB_abPARK[5]
034: SUB_abSARI[4]
038: SUB_bPLI
039: SUB_bLAL
03A: SUB_abARIplusRPN[5]
03F: SUB_boZAP
040: SUB_bZAP
041: SUB_boServiceClass
042: SUB_bServiceClass
043: AK_boUAKavailable
044: AK_boUAKproven
045: AK_abUAK_or_AC [16]
All 0x00
x
0101
0
EEP_HsRegistInfoLog
Record of the Handset Regist Information by Cancel
Handset or Cancel Base. (Return Survey)
0:Not Registered.
1:Registered.
2:Deleted by Cancel Base.
3:Deleted by Cancel Handset.
Handset or Cancel Base. (Return Survey)
0:Not Registered.
1:Registered.
2:Deleted by Cancel Base.
3:Deleted by Cancel Handset.
0x00
x
010A
1
EEP_DspSppHaqc
DSP Parameter of HAGC
0x9A, 0x19, 0x7B,
0x14, 0x08, 0x00,
0x00, 0x00, 0x7B,
0x14, 0xED, 0x00,
0xE6, 0x7E
x
47
VL-GD001RU
Click on the first or last page to see other VL-GD001RU service manuals if exist.