Read Panasonic SB-HF560E / SB-HS560E / SB-HC560E Service Manual online
For SB-HF560
Type
Type
1 way, 1 speaker system (Bass reflex)
Speaker unit(s)
Impedance 3
!
Full range
6.5 cm Cone type
Input power (IEC)
125 W* (Max)
Output sound pressure
80 dB/W (1.0 m)
Frequency range
76 Hz to 25 kHz (-16 dB)
89 Hz to 22 kHz (-10 dB)
89 Hz to 22 kHz (-10 dB)
Dimensions (W x H x D)
252 mm x 1123 mm x 235 mm
Mass
3.7 kg
For SB-HS560
Type
1 way, 1 speaker system (Bass reflex)
Speaker unit(s)
Impedance 3
!
Full range
6.5 cm Cone type
Input power (IEC)
125 W* (Max)
Output sound pressure
80 dB/W (1.0 m)
Frequency range
95 Hz to 25 kHz (-16 dB)
120 Hz to 22 kHz (-10 dB)
Dimensions (W x H x D)
92 mm x 142 mm x 95 mm
SB-HF560E
SB-HS560E
SB-HC560E
Colour
(S)... Silver Type
(K)... Black Type
(K)... Black Type
Mass
0.6 kg
For SB-HC560
Type
2 way, 2 speaker system (Bass reflex)
Speaker unit(s)
Impedance 6
!
1. Full range
6.5 cm Cone type
2. Full range
6.5 cm Cone type
Input power (IEC)
250 W* (Max)
Output sound pressure
82 dB/W (1.0 m)
Cross over frequency
5 kHz
Frequency range
80 Hz to 25 kHz (-16 dB)
96 Hz to 22 kHz (-10 dB)
96 Hz to 22 kHz (-10 dB)
Dimensions (W x H x D)
270 mm x 94 mm x 95 mm
Mass
1.3 kg
Notes :
1. Specifications are subject to change without notice.
Mass and dimensions are approximate.
Mass and dimensions are approximate.
2. Total harmonic distortion is measured by the digital spectrum
analyzer.
* : Rating with low-cut filter equipped amplifier.
analyzer.
* : Rating with low-cut filter equipped amplifier.
Speaker System
Specification
ORDER NO. MD0801010CE
2
SB-HF560E / SB-HS560E / SB-HC560E
1 Assembling and Disassembling
“ATTENTION SERVICER”
Some chassis components may have sharp edges. Be careful when disassembling and servicing.
1. This section describes procedures for checking the operation and replacing the main components.
2. For reassembly after operation checks or replacement, reverse the respective procedures.
2. For reassembly after operation checks or replacement, reverse the respective procedures.
Special reassembly procedures are described only when required.
3. Select items from the following index when checks or replacement are required.
4. Refer to the Parts No. on the page of “Parts Location and Replacement Parts List” (Section 6), if necessary.
4. Refer to the Parts No. on the page of “Parts Location and Replacement Parts List” (Section 6), if necessary.
Below is the list of disassembly sections
# For SB-HF560E-S/K
Disassembly of Upper box assembly
Disassembly of Upper rear cabinet assembly
Disassembly of Woofer (SP1)
Disassembly of Terminal
Disassembly of Lower box assembly
Disassembly of Lower rear cabinet assembly
Disassembly of Stand base assembly
Disassembly of Upper rear cabinet assembly
Disassembly of Woofer (SP1)
Disassembly of Terminal
Disassembly of Lower box assembly
Disassembly of Lower rear cabinet assembly
Disassembly of Stand base assembly
# For SB-HS560E-S/K
Disassembly of Rear cabinet assembly
Disassembly of Woofer unit (SP1)
Disassembly of Terminal
Disassembly of Woofer unit (SP1)
Disassembly of Terminal
# For SB-HC560E-S/K
Disassembly of Rear cabinet assembly
Disassembly of Woofer unit 1 (SP1)
Disassembly of Woofer unit 2 (SP1)
Disassembly of Terminal
Disassembly of Woofer unit 1 (SP1)
Disassembly of Woofer unit 2 (SP1)
Disassembly of Terminal
3
SB-HF560E / SB-HS560E / SB-HC560E
1.1. For SB-HF560E-S/K
1.1.1. Disassembly of Upper box
assembly
Step 1: Detach the white (+) and blue (-) speaker wires.
Step 2: Detach the speaker wires from the groove of upper box
assembly.
Step 2: Detach the speaker wires from the groove of upper box
assembly.
Step 3: Remove 1 screw.
Step 4: Detach the upper box assembly as arrow shown.
1.1.2. Disassembly of Upper rear cabinet
assembly
Follow (Step 1) to (Step 4) in item 1.1.1.
Step 1: Remove 10 screws.
Step 2: Hold down the upper front panel and lift up the upper
rear cabinet assembly.
rear cabinet assembly.
4
SB-HF560E / SB-HS560E / SB-HC560E