Read Panasonic SB-HF100P / SB-HS100P / SB-HC100P Service Manual online
For SB-HF100
Type
Type
2 way, 3 speaker system (Bass reflex)
Speaker unit(s)
Impedance 6
Ω
1. Woofer
6.5 cm (2-1/2”) Cone type x 2
2. Tweeter
6 cm (2-3/8”) Cone type
Input power (IEC)
250 W (Max)*
Output sound pressure
83 dB/W (1.0 m)
Frequency range
80 Hz to 25 kHz (-16 dB)
93 Hz to 22 kHz (-10 dB)
Dimensions (W x H x D)
121 mm x 328 mm x 129 mm
(4-25/32” x 12-15/16” x 5-3/32”)
Mass (Weight)
Approx. 1.7 kg (3.7 lbs)
93 Hz to 22 kHz (-10 dB)
For SB-HS100
Type
1 way, 1 speaker system (Bass reflex)
Speaker unit(s)
Impedance 3
Ω
1. Full range
6.5 cm (2-1/2”) Cone type
Input power (IEC)
150 W (Max)*
Output sound pressure
80 dB/W (1 m)
Frequency range
82 Hz to 25 kHz (-16 dB)
92 Hz to 22 kHz (-10 dB)
Dimensions (W x H x D)
121 mm x 328 mm x 129 mm
SB-HF100P
SB-HS100P
SB-HC100P
Colour
(K)... Black Type
(K)... Black Type
(4-25/32” x 12-15/16” x 5-3/32”)
Mass (Weight)
Approx. 1.0 kg (2.2 lbs)
For SB-HC100
Type
Type
2 way, 3 speaker system (Bass reflex)
Speaker unit(s)
Impedance 6
Ω
1. Woofer
6.5 cm (2-1/2”) Cone type x 2
2. Tweeter
6 cm (2-3/8”) Cone type
Input power (IEC)
250 W (Max)*
Output sound pressure
83 dB/W (1 m)
Frequency range
80 Hz to 25 kHz (-16 dB)
93 Hz to 22 kHz (-10 dB)
Dimensions (W x H x D)
301 mm x 111 mm x 134 mm
(11-7/8” x 4-3/8” x 5-9/32”)
Mass (Weight)
Approx. 1.6 kg (3.5 lbs)
Notes:
1. Specifications are subject to change without notice. Mass and
dimensions are approximate.
dimensions are approximate.
2. Total harmonic distortion is measured by the digital spectrum
analyzer.
analyzer.
* Rating with the low cut filter equipped amplifier.
Speaker System
Specification
ORDER NO. MD0804012CE
A6
2
SB-HF100P / SB-HS100P / SB-HC100P
1 Assembling and Disassembling
“ATTENTION SERVICER”
Some chassis components may have sharp edges. Be careful when disassembling and servicing.
1. This section describes procedures for checking the operation and replacing the main components.
2. For reassembly after operation checks or replacement, reverse the respective procedures.
Special reassembly procedures are described only when required.
3. Select items from the following index when checks or replacement are required.
4. Refer to the Parts No. on the page of “Parts Location and Replacement Parts List” (Section 5), if necessary.
Below is the list of disassembly sections
• For SB-HF100P-K
Disassembly of Stand
Disassembly of Net frame assembly
Disassembly of Tweeter (SP1)
Disassembly of Woofer 1 (SP2)
Disassembly of Woofer 2 (SP2)
Disassembly of Rear cabinet assembly
Disassembly of Terminal
• For SB-HS100P-K
Disassembly of Stand
Disassembly of Net frame assembly
Disassembly of Full range (SP1)
Disassembly of Rear cabinet assembly
Disassembly of Terminal
• For SB-HC100P-K
Disassembly of Net frame assembly
Disassembly of Tweeter (SP1)
Disassembly of Woofer 1 (SP2)
Disassembly of Woofer 2 (SP2)
Disassembly of Rear cabinet assembly
Disassembly of Terminal
3
SB-HF100P / SB-HS100P / SB-HC100P
1.1. SB-HF100P-K
1.1.1. Disassembly of Stand
Step 1: Remove 3 screws.
Step 2: Remove stand.
1.1.2. Disassembly of Net frame
assemably
Follow (Step 1) to (Step 2) in item 1.1.1.
Step 1: Insert steel rule with cloth as shown.
Step 2: Apply force gently to push out the net frame assembly.
Caution: Do not exert too much force as it may damage the net
frame assembly.
frame assembly.
4
SB-HF100P / SB-HS100P / SB-HC100P
