Read Panasonic SA-PM86DGCS / SA-PM86DEE / SC-PM86DEE Service Manual online
I AMPLIFIER SECTION
RMS Output Power
RMS Output Power
THD 10%
80 W per channel (3
Ω), 1 kHz
Total RMS Dolby Digital Mode
power
power
160 W
PMPO Output Power
1800 W
I FM/AM TUNER, TERMINALS SECTION
Preset station
FM 30 stations
AM 15 stations
Frequency Modulation (FM)
Frequency range
87.50 to 108.00 MHz
(50 kHz step)
Sensitivity
2.5 µV (IHF)
S/N 26dB
2.2 µV
Antenna terminals
75
Ω (unbalanced)
Amplitude Modulation (AM)
Frequency range
522 to 1629 kHz (9 kHz step)
520 to 1630 kHz (10 kHz step)
(GCS)
AM Sensitivity S/N 20 dB at 999
kHz
kHz
1000 µV/m
Digital audio output
Coaxial digital output
Pin jack
Music Port (front)
SA-PM86DGCS
SA-PM86DEE
Colour
(K)... Black Type
(K)... Black Type
Sensitivity
100 mV, 10 k
Ω
Terminal
Stereo, 3.5 mm jack
Phone jack
Terminal
Stereo, 3.5 mm jack
Output level (CD, 1 kHz, -20dB)
32
Ω
Mic jack
Sensitivity
0.7 mV, 600
Ω
Terminal
Mono, 3.5 mm jack (2 system)
I VIDEO SECTION
Video system
PAL625/50, PAL525/60, NTSC
Composite video output
Output level
1 Vp-p (75
Ω)
Terminal
Pin jack (1 system)
Component video output
Y output level
1 Vp-p (75
Ω)
P
B
output level
0.7 Vp-p (75
Ω)
P
R
output level
0.7 Vp-p (75
Ω)
Terminal
Pin jack (Y: green, P
B
: blue, P
R
:
red) (1 system)
HDMI AV output
Terminal
Type A connector (19 pin)
This unit supports “HDAVI Control 2” function
I USB SECTION
DVD Stereo System
Notes: This model’s mechanism unit is DLS6. Please refer to the original Service Manual (Order No.
MD0801003CE) for this mechanism.
MD0801003CE) for this mechanism.
Specifications
ORDER NO. MD0803011CE
USB Port
USB Standard
USB 2.0 full speed
Media file format support
MP3 (*.mp3)
WMA (*.wma)
JPEG (*.jpg, *.jpg)
MPEG4 (*.asf)
USB device file system
FAT12, FAT16, FAT32
USB port power
500 mA (Max)
I DISC SECTION
Discs played (8 cm or 12 cm)
Discs played (8 cm or 12 cm)
(1) DVD (DVD-Video, DivX
*6, *7
)
(2) DVD-RAM (DVD-VR, MP3
*2, *7
, JPEG
*4, *7
, MPEG4
*5, *7
, DivX
*6, *7
)
(3) DVD-R (DVD-Video, DVD-VR, MP3
*2, *7
, JPEG
*4, *7
, MPEG4
*5, *7
,
DivX
*6, *7
)
(4) DVD-R DL (DVD-Video, DVD-VR)
(5) DVD-RW (DVD-Video, DVD-VR, MP3
*2, *7
, JPEG
*4, *7
, MPEG4
*5, *7
,
DivX
*6, *7
)
(6) +R/+RW (Video)
(7) +R DL (Video)
(8) CD, CD-R/RW (CD-DA, Video CD, SVCD
*1
, MP3
*2, *7
, WMA
*3, *7
,
JPEG
*4, *7
, MPEG4
*5, *7
, DivX
*6, *7
)
*
1
Conforming to IEC62107
*
2
MPEG-1 Layer 3, MPEG-2 Layer 3
*
3
Windows Media Audio Ver.9.0 L3
Not compatible with Multiple Bit Rate (MBR)
*
4
Exif Ver 2.1 JPEG Baseline files
Picture resolution: between 160 x 120 and 6144 x 4096 pixels
(Sub sampling is 4:0:0, 4:2:0, 4:2:2 or 4:4:4). Extremely long and
narrow pictures may not be displayed.
*
5
MPEG4 data recorded with Panasonic SD multi cameras or DVD
video recorders
Conforming to SD VIDEO speci. cations (ASF standard)/MPEG4
(Simple Profile) video system/G.726 audio system
1
Safety Precautions
3
2
Prevention of Electro Static Discharge (ESD) to
Electrostatically Sensitive (ES) Devices
5
3
Precaution of Laser Diode
6
4
Handling Precautions for Traverse Unit
7
5
Handling the Lead Free Solder
9
6
Operation Procedures
10
7
Self-Diagnosis and Special Mode Setting
16
8
Assembling and Disassembling
28
9
Assembling and Disassembling of Mechanism Unit
51
10 Service Fixture and Tools
55
*
6
Plays all versions of DivX
®
video (including DivX
®
6) with standard
playback of DivX
®
media files. Certified to the DivX Home Theater
Profile.
*
7
The total combined maximum number of recognizable audio,
picture and video contents and groups: 4000 audio, picture and
video contents and 400 groups.
Pick up
Wavelength (DVD/CD)
655/785 nm
Laser power (DVD/CD)
CLASS 1/CLASS 1M
Audio output (Disc)
Number of channels
2 channels (FL, FR)
I GENERAL
Power supply
AC 230 V, 50 Hz (EE)
AC 220 to 240 V, 50/60 Hz
(GCS)
Power consumption
95 W
Dimensions (WxHxD)
175.0 mm x 240.0 mm x 342.3
mm
Mass
4.5 kg
Operating temperature range
0°C to 40°C
Operating humidity range
35% to 80% RH (no
condensation)
Power consumption in standby mode
approx. 0.7 W
I SYSTEM
SC-PM86DEE-K
Main unit: SA-PM86DEE-K
Speakers: SB-PM86EG-K
SC-PM86DGCS-K
Main unit: SA-PM86DGCS-K
Speakers: SB-PM86EG-K
Note:
1.
Specifications are subject to change without notice. Mass and
dimensions are approximate.
dimensions are approximate.
2.
Total harmonic distortion is measured by the digital spectrum
analyzer.
analyzer.
11 Service Position
56
12 Voltage Measurement & Waveform Chart
61
13 Wiring Connection Diagram
69
14 Block Diagram
71
15 Notes Of Schematic Diagram
77
16 Schematic Diagram
79
17 Printed Circuit Board
95
18 Illustration of IC’s, Transistors and Diodes
101
19 Terminal Function of IC’s
102
20 Exploded Views
105
21 Replacement Parts List
109
CONTENTS
Page
Page
2
SA-PM86DGCS / SA-PM86DEE
1.1.2. Leakage Current Hot Check
1 Safety Precautions
1.1. General Guidelines
1. When servicing, observe the original lead dress. If a short circuit is found, replace all parts which have been overheated or
damaged by the short circuit.
2. After servicing, ensure that all the protective devices such as insulation barriers, insulation papers shields are properly installed.
3. After servicing, check for leakage current checks to prevent from being exposed to shock hazards.
1.1.1. Leakage Current Cold Check
1. Unplug the AC cord and connect a jumper between the two prongs on the plug.
2. Using an ohmmeter measure the resistance value, between the jumpered AC plug and each exposed metallic cabinet part on
the equipment such as screwheads, connectors, control shafts, etc. When the exposed metallic part has a return path to the
chassis, the reading should be between 1M
chassis, the reading should be between 1M
Ω and 5.2Ω.
When the exposed metal does not have a return path to the chassis, the reading must be
.
1. Plug the AC cord directly into the AC outlet. Do not use an isolation transformer for this check.
2. Connect a 1.5k
Ω, 10 watts resistor, in parallel with a 0.15µF capacitors, between each exposed metallic part on the set and a
good earth ground such as a water pipe, as shown in Figure 1.
3. Use an AC voltmeter, with 1000 ohms/volt or more sensitivity, to measure the potential across the resistor.
4. Check each exposed metallic part, and measure the voltage at each point.
5. Reverse the AC plug in the AC outlet and repeat each of the above measurements.
6. The potential at any point should not exceed 0.75 volts RMS. A leakage current tester (Simpson Model 229 or equivalent) may
be used to make the hot checks, leakage current must not exceed 1/2 milliamp. should the measurement is outside of the limits
specified, there is a possibility of a shock hazard, and the equipment should be repaired and re-checked before it is returned
to the customer.
specified, there is a possibility of a shock hazard, and the equipment should be repaired and re-checked before it is returned
to the customer.
Figure 1
3
SA-PM86DGCS / SA-PM86DEE
1.2. Before Repair and Adjustment
Disconnect AC power, discharge Power Supply Capacitors C2207, C2210, C2211, C2212, C2742, C5105, C5106, C5916, C5917,
C5938, C5562, C5954, C5979 and C5993 through a 10
C5938, C5562, C5954, C5979 and C5993 through a 10
Ω, 1W resistor to ground.
DO NOT SHORT-CIRCUIT DIRECTLY (with a screwdriver blade, for instance), as this may destroy solid state devices.
After repairs are completed, restore power gradually using a variac, to avoid overcurrent.
• Current consumption at AC 220 - 240 V, at 50/60 Hz in NO SIGNAL mode (at volume min) should be ~500 mA. (GCS)
• Current consumption at AC 230 V 50 Hz in NO SIGNAL mode (at volume min) should be ~500 mA. (EE)
• Current consumption at AC 230 V 50 Hz in NO SIGNAL mode (at volume min) should be ~500 mA. (EE)
1.3. Protection Circuitry
The protection circuitry may have operated if either of the following conditions are noticed:
• No sound is heard when the power is turned on.
• Sound stops during a performance.
The function of this circuitry is to prevent circuitry damage if, for example, the positive and negative speaker connection wires are
"shorted", or if speaker systems with an impedance less than the indicated rated impedance of the amplifier are used.
• Sound stops during a performance.
The function of this circuitry is to prevent circuitry damage if, for example, the positive and negative speaker connection wires are
"shorted", or if speaker systems with an impedance less than the indicated rated impedance of the amplifier are used.
If this occurs, follow the procedure outlines below:
1. Turn off the power.
2. Determine the cause of the problem and correct it.
3. Turn on the power once again after one minute.
Note:
When the protection circuitry functions, the unit will not operate unless the power is first turned off and then on again.
1.4. Safety Part Information
Safety Parts List:
There are special components used in this equipment which are important for safety.These parts are marked by
in the
Schematic Diagrams & Replacement Parts List. It is essential that these critical parts should be replaced with manufacturer’s
specified parts to prevent shock, fire or other hazards. Do not modify the original design without permission of manufacturer.
specified parts to prevent shock, fire or other hazards. Do not modify the original design without permission of manufacturer.
Table 1
Reference No.
Part No.
Part Name & Description
Remarks
A2
K2CQ2CA00006
AC CORD
[M]GCS
A2
K2CQ2CA00007
AC CORD
[M]EE
JK5970
K2AA2B000017
AC INLET
[M]
T5900
G5CYBYY0 0007
POWER TRANSFORMER
[M]
T5901
G4C2AAJ00005
POWER TRANSFORMER
[M]
F5970
K5D162BLA013
FUSE
[M]
L5970
ELF15N035AN
LINE FILTER
[M]
RL5970
K6B1AEA00003
POWER RELAY
[M]
Z5970
ERZVA5Z471
ZENER
[M]
FP5920
K5G402A00025
FUSE PROTECTOR
[M]
FP5921
K5G102A00039
FUSE PROTECTOR
[M]
FP5922
K5G202AA0002
FUSE PROTECTOR
[M]
PCB7
REPX0633D
TRANSFORMER P.C.B.
[M]RTL
4
SA-PM86DGCS / SA-PM86DEE
