Read Panasonic SA-PM54E / SA-PM54EG Service Manual online
Pin No.
Mark
I/O
Function
1
IN2
I
Motor Driver Input
2
PC2
I
Turntable Motor Drive Signal
(“L”:ON)
(“L”:ON)
3
IN1
I
Motor Drive (1) Input
4
PC1
-
Traverse Motor Drive Signal
(“L”): ON)
(“L”): ON)
5-8
N.C.
-
No Connection
9
PGND1
-
Ground Connection (1) for Drive
10
PVCC1
-
Power Supply (1) for Drive
11
D1-
O Motor Drive (1) reverse - action
output
12
D1+
O Motor Drive (1) forward - action
output
13
D2-
O Motor Drive (2) reverse - action
output
14
D2+
O Motor Drive (2) forward - action
output
Pin No.
Mark
I/O
Function
1
CHANGE_
SW
I
Change Switch (CR16)
2
TU_TUNED
I
Tuner tuned signal
3
TU_ST
I
Tuner Stereo signal
4
TU_CL
I
Tuner Serial Clock Input
5
TU_ SDA
I/O
Tuner Serial Data Input
6
N.C.
-
Microcomputer Beat Proof
Output 1 (CONTROL)
Output 1 (CONTROL)
7
N.C.
-
Microcomputer Beat Proof
Output 2 (CONTROL)
Output 2 (CONTROL)
8
BYTE
-
External Data Bus Width Select
Input (Connect to Ground)
Input (Connect to Ground)
9
CNVSS/EFP_C
NVSS
-
Flash Mode Terminal
(Connected To Ground)
(Connected To Ground)
10
XCIN
I
A/32.768 kHz Sub Clock
11
XCOUT
O
32.768 kHz Sub Clock
12
/RESET/EFP_R
ESET
I
Reset Input (ACTIVE L)
13
XOUT
O
10 MHz Main Clock
14
VSS
-
Ground ( 0V )
15
XIN
I
10 MHz Main Clock
16
VCC
-
Power Supply (+5V )
17
/NMI
-
Connect to Vcc (+5V)
18
RMT
I
Remote Control Input
19
BLKCK
I
CD Block Clock Input ( Inverted
)
)
20
HALT
I
AC Failure Detect Input
21
PCONT2
O
HIC Mute
22
EE_CS/
O
EEPROM Chip Select
23
EE_CLK
O
EEPROM CLOCK
24
N.C.
-
No Connection
25
N.C.
-
No Connection
26
FL_CS1
O
FL Driver Chip Select ( Master )
27
N.C.
-
No Connection
28
FL_CLK
O
Serial Clock to FL Driver
29
N.C.
O
Reset Input(ACTIVE L)
30
FL_DOUT
O
Serial Data To FL Driver
( Output )
( Output )
31
RXD
-
No Connection (For Download
Software)
Software)
32
TXD
-
No Connection (For Download
Software)
Software)
33
SCLK
-
No Connection (For Download
Software)
Software)
34
BUSY
-
No Connection (For Download
Software)
Software)
35
N.C.
-
No Connection
Pin No.
Mark
I/O
Function
15
D3-
O Motor Drive (3) reverse - action
output
16
D3+
O Motor Drive (3) forward - action
output
17
D4-
O Motor Drive (4) reverse - action
output
18
D4+
O Motor Drive (4) forward - action
output
19
PVCC2
-
Power Supply (2) for Driver
20
PGND2
-
Ground Connection (2) for Driver
21-24
N.C.
-
No Connection
25
VCC
-
Power Supply terminal
26
VREF
-
Reference Voltage Input
27
IN4
I
Motor Driver (4) Input
28
IN3
I
Motor Driver (3) Input
Pin No.
Mark
I/O
Function
36
N.C.
-
No Connection
37
N.C.
-
No Connection
38
N.C.
-
No Connection
39
MCLK
O
CD Command CLK Output
40
MUTE_A
O
Audio Mute
41
EPM
-
-
42
MDATA_
OUT
O
CD Command Data Output
43
MLD
O
CD Command Load Output/
44
N.C.
-
RDS Clock Input
45
N.C.
-
No Connection
46
CE
-
Chip Enable
47
DCDET
I
DC Detect Input
48
STATUS
I
CD Servo LSI Status
Input(Inverted)
Input(Inverted)
49
PCONT
O
Main Transformer Control
Output
Output
50
PLAY_SW
I
Play Sw (CR16)
51
STOCK_SW
I
Stock Sw (CR16)
52
OP_SW
I
Open Sw (CR16)
53
POS
I
Position Sw (CR16)
54
BT_SW
I
Bottom Sw (CR16)
55
M1_R
O
Changer Motor 1 Reverse
Control
Control
56
M1_F
O
Changer Motor 1 Forward
Control
Control
57
M2_R
O
Changer Motor 2 Reverse
Control
Control
58
M2_F
O
Changer Motor 2 Forward
Control
Control
59
REC
O
When record circuit is
operatingDURING RECORDING
= H
operatingDURING RECORDING
= H
60
N.C.
O
No Connection
61
PHOTO
I
PHOTO (SG Mechanism only)
62
VCC
-
Power Supply ( +5V )
63
EE_DAT
I/O
EEPROM DATA
64
VSS
-
Ground ( 0V )
65
DMT
O
Deck Mute at mecha
transitionL=mute OFF, H=mute
ON
transitionL=mute OFF, H=mute
ON
66
N.C.
-
No Connection
67
ASP_CLK
O
ASP CLK
68
ASP_DAT
O
ASP DATA
69
N.C.
-
No Connection
70
RDS_DAT
-
RDS Data Input
71
RDS_CLK
-
RDS Clock Input
20.2. IC7002 (BA5948FPE2) IC 4CH Drive
20.3. IC401 (C2CBYY000213) IC MICRO-PROCESSOR
101
SA-PM54E / SA-PM54EG
Click on the first or last page to see other SA-PM54E / SA-PM54EG service manuals if exist.