Read LG 60PZ950B-SA (CHASSIS:PB12A) Service Manual online
5-6. Auto adjustment
* Auto-control interface and directions
(1) Adjust in the place where the influx of light like floodlight
(1) Adjust in the place where the influx of light like floodlight
around is blocked. (Illumination is less than 10ux).
2) Measure and adjust after sticking the Color Analyzer (CA-
100+, CA210) to the side of the module.
3) Aging time :
After aging start, keep the Power on (no suspension of
power supply) and heat-run over 5 minutes
power supply) and heat-run over 5 minutes
V
RS-232C COMMAND(Commonly apply)
O
example
“wb 00 00”: Start Auto-adjustment of white balance.
“wb 00 10”: Start Gain Adjustment (Inner pattern)
“jb 00 c0” :
…
“wb 00 1f”: End of Adjustment
“wb 00 10”: Start Gain Adjustment (Inner pattern)
“jb 00 c0” :
…
“wb 00 1f”: End of Adjustment
* If it needs, offset adjustment (wb 00 20-start, wb 00 2f-
end)
“wb 00 ff”: End of white balance adjustment (inner pattern
disappear)
V
Adjustment Mapping information
O
When Color temperature (White balance) Adjustment
(Automatically)
(Automatically)
O
Press “Power only key” of service remocon and operate
automatically adjustment.
automatically adjustment.
O
Set BaudRate to 115200.
O
You must start “wb 00 00” and finish it “wb 00 ff”.
O
If it needs, then adjustment “Offset”.
6. Checking the EYE-Q Operation.
(1) Press the EYE Key on the adjustment remote controller.
(2) Check the Sensor DATA ( It must be under 10) and keep
(2) Check the Sensor DATA ( It must be under 10) and keep
the data longer than 1.5s
(3) Check ‘OK’
(Sensor DATA 0 ~ 4095, Power Saving Mode 0 ~ 12)
* IF you press IN-STAP Button, change Green Eye-check OSD.
7. Ping TEST
* This test is to check Network operation.
7-1. Equipment Setting
(1) Play the LAN Port Test PROGRAM.
(2) Input IP set up for an inspection to Test
(2) Input IP set up for an inspection to Test
*IP Number : 12.12.2.2
7-2. LAN PORT inspection (PING TEST)
* In this case Network setting is on Manual Setting.
(1) Play the LAN Port Test Program.
(2) connect each other LAN Port Jack.
(3) Play Test (F9) button and confirm OK Message.
(4) remove LAN CABLE
(1) Play the LAN Port Test Program.
(2) connect each other LAN Port Jack.
(3) Play Test (F9) button and confirm OK Message.
(4) remove LAN CABLE
- 11 -
Min
Tpy
Max
R-GAIN
0
192
192
G-GAIN
0
192
192
B-GAIN
0
192
192
RS-232C COMMAND
[CMD ID DATA]
Meaning
wb
00
00
White Balance adjustment start.
wb
00
10
Start of adjust gain
(Inner white pattern)
wb
00
1fEnd of
gain adjust
wb
00
20
Start of offset adjust
(Inner white pattern)
wb
00
2f
End of offset adjust
wb
00
ff
End of White Balance adjust
(Inner pattern disappeared)
RS-232C COMMAND
CENTER
[CMD ID DATA]
MIN
(DEFAULT)
MAX
Cool Mid
Warm
Cool
Mid
Warm
R Gain
jg
Ja
jd
00
184
192
192
192
G Gain
jh
Jb
je
00
187
183
159
192
B Gain
ji
Jc
jf00
192
161
95
192
R Cut
64
64
64
127
G Cut
64
64
64
127
B Cut
64
64
64
127
Click on the first or last page to see other 60PZ950B-SA (CHASSIS:PB12A) service manuals if exist.