60PZ850B-SA (CHASSIS:PB11A) - LG TV Service Manual (repair manual). Page 6

Read LG 60PZ850B-SA (CHASSIS:PB11A) Service Manual online

- 6 -
ADJUSTMENT INSTRUCTION
1. Application Range
This spec. sheet applies to PB11A Chassis applied PDP TV
all models manufactured in TV factory.
2. Specification
(1) Because this is not a hot chassis, it is not necessary to use
an isolation transformer. However, the use of isolation
transformer will help protect test instrument.
(2) Adjustment must be done in the correct order. But it is
flexible when its factory local problem occurs.
(3) The adjustment must be performed in the circumstance of
25 
c
C ± 5 cC of temperature and 65 % ± 10 % of relative
humidity if there is no specific designation.
(4) The input voltage of the receiver must keep 100 V - 240 V,
50 / 60 Hz.
(5) Before adjustment, execute Heat-Run for 5 minutes.
V
After Receive 100% Full white pattern (06CH) then
process Heat-run 
(or “8. Test pattern” condition of Ez-Adjust status)
V
How to make set white pattern 
1) Press Power ON button of Service Remocon
2) Press ADJ button of Service remocon. Select “10.
Test pattern” and, after select “White” using
navigation button, and then you can see 100% Full
White pattern. 
* In this status you can maintain Heat-Run useless any
pattern generator
* Notice: if you maintain one picture over 20 minutes
(Especially sharp distinction black with white pattern –
13Ch, or Cross hatch pattern – 09Ch) then it can
appear image stick near black level. 
3. Adjustment items
3-1. PCB Assembly adjustment
(1) Adjust 480i Comp1 
(2) Adjust 1080p Comp1/RGB 
- If it is necessary, it can adjustment at Manufacture Line
- You can see set adjustment status at “9. ADJUST
CHECK” of the “In-start menu” 
3-2. Set Assembly Adjustment
(1) EDID (The Extended Display Identification Data )
(2) Color Temperature (White Balance) Adjustment
(3) Make sure RS-232C control
(4) Selection Factory output option
4. PCB Assembly Adjustment
4-1. Using RS-232C
- Adjust 3 items at 3-1 PCB assembly adjustments 
“ (3) Adjustment sequence” one after the order.
(1) Adjustment protocol
(2) Necessary items before Adjustment items
O
Pattern Generator : (MSPG-925FA)
O
Adjust 480i Comp1 
(MSPG-925FA:model :209, pattern :65) – Comp1 Mode
O
Adjust 1080p Comp1 
(MSPG-925FA:model :225 , pattern :65) – Comp1 Mode
O
Addjust RGB (MSPG-925FA:model :225 , pattern :65) 
– RGB-PC Mode
* If you want more information then see the below Adjustment
method (Factory Adjustment)
(3) Adjustment sequence
O
aa 00 00: Enter the ADC Adjustment mode.
O
xb 00 40: Change the mode to Component1 (No actions)
O
ad 00 10: Adjust 480i Comp
O
ad 00 10: Adjust 1080p comp
O
xb 00 60: Change to RGB-PC mode(No action)
O
ad 00 10: Adjust 1080p RGB
O
xb 00 90: Endo of Adjustmennt
< See ADC Adjustment RS232C Protocol_Ver1.0 >
Order           Command
Set response
1. Inter the
aa 00 00
a 00 OK00x
Adjustment 
mode
2. Change the
XB 00 40
b 00 OK40x (Adjust 480i Comp1 )
Source
XB 00 60
(Adjust 1080p Comp1)
b 00 OK60x (Adjust 1080p RGB)
3. Start
ad 00 10
Adjustment
4. Return the
OKx ( Success condition )
Response
NGx ( Failed condition )
5. Read data
( main )
(main : component1 480i, RGB 1080p)
Adjustment
ad 00 20
00000000000000000000000007c007b006dx
data
( main )
(main : component1 480i, RGB 1080p)
ad 00 30
000000070000000000000000007c00830077x
6. Confirm
ad 00 99
NG 03 00x (Failed condition)
Adjustment
NG 03 01x (Failed condition)
NG 03 02x (Failed condition)
OK 03 03x (Success condition)
7. End of
ad 00 90
d 00 OK90x
Adjustment
Page of 72
Display

Click on the first or last page to see other 60PZ850B-SA (CHASSIS:PB11A) service manuals if exist.