Read LG 50PQ30TD-SB (CHASSIS:PB91A) Service Manual online
O
RS-232C Command (Commonly apply)
- “wb 00 00”: Start Auto-adjustment of white balance.
- “wb 00 10”: Start Gain Adjustment (Inner pattern)
- “jb 00 c0” :
- ...
- “wb 00 1f”: End of Adjustment
- If it needs, offset adjustment (wb 00 20-start, wb 00 2f-end)
- “wb 00 ff”: End of white balance adjustment (inner pattern
- “wb 00 10”: Start Gain Adjustment (Inner pattern)
- “jb 00 c0” :
- ...
- “wb 00 1f”: End of Adjustment
- If it needs, offset adjustment (wb 00 20-start, wb 00 2f-end)
- “wb 00 ff”: End of white balance adjustment (inner pattern
disappear)
Notice) Adjustment Mapping information
O
When Color temperature (White balance) Adjustment
(Automatically)
- Press “Power only key” of service remocon and operate
- Press “Power only key” of service remocon and operate
automatically adjustment.
- Set BaudRate to 115200.
O
You must start “wb 00 00” and finish it “wb 00 ff”.
O
If it needs, then adjustment “Offset”.
7-4. White Balance Adjustment (Manual
Adjustment)
(1) Test Equipment: CA-210
Using PDP color temperature, Color Analyzer (CA-210)
must use CH 10, which Matrix compensated (White, Red,
Green, Blue compensation) with CS-2100. See the
Coordination bellowed one.
must use CH 10, which Matrix compensated (White, Red,
Green, Blue compensation) with CS-2100. See the
Coordination bellowed one.
(2) Manual adjustment sequence is like bellowed one.
1) Turn to “Ez-Adjust” mode with press ADJ button of
service remocon.
2) Select “10.Test Pattern” with CH+/- button and press
enter. Then set will go on Heat-run mode. Over 30
minutes set let on Heat-run mode.
minutes set let on Heat-run mode.
3) Let CA-210 to zero calibration and must has gap more
10cm from center of PDP module when adjustment.
4) Press “ADJ” button of service remocon and select
“7.White-Balance” in “Ez-Adjust” then press “
G
” button
of navigation key.
(When press “
(When press “
G
” button then set will go to full white
mode)
5) Adjust at three mode (Cool, Medium, Warm)
6) If “cool” mode
6) If “cool” mode
Let B-Gain to 192 and R, G, B-Cut to 64 and then
control R, G gain adjustment High Light adjustment.
control R, G gain adjustment High Light adjustment.
7) If “Medium” and “Warm” mode Let R-Gain to 192 and R,
G, B-Cut to 64 and then control G, B gain adjustment
High Light adjustment.
High Light adjustment.
8) All of the three mode
Let R-Gain to 192 and R, G, B-Cut to 64 and then
control G, B gain adjustment High Light adjustment.
control G, B gain adjustment High Light adjustment.
9) With volume button (+/-) you can adjust.
10) After all adjustment finished, with Enter (
10) After all adjustment finished, with Enter (
V
key) turn to
Ez-Adjust mode. Then with ADJ button, exit from
adjustment mode
adjustment mode
O
White Balance adjustment coordination and color temperature.
(1) Using CS-1000 Equipment.
- COOL : T=11000K,
∆
uv=0.000, x=0.276 y=0.283
- MEDIUM : T=9300K,
∆
uv=0.000, x=0.285 y=0.293
- WARM : T=6500K,
∆
uv=0.000, x=0.313 y=0.329
(2) Using CA-210 Equipment. (10 CH)
Contrast value: 216 Gray
- 14 -
Click on the first or last page to see other 50PQ30TD-SB (CHASSIS:PB91A) service manuals if exist.