50PQ30R-MA (CHASSIS:PP91A) - LG TV Service Manual (repair manual). Page 14

- Maintain the white balance adjustment mode with same

condition of Heat-run 

- Maintain after AC off/on in status of Heat-run pattern display

(2) Release the white balance adjustment mode

- Release the adjust mode after AC off/on or std-by off/on in

status of finishing the Hear-run mode

- Release the Adjust mode when receiving the aging off

command(F3 00 00) from adjustment equipment)

(3) Enter the adjust mode of white balance

- Enter the white balance adjustment mode with aging

command(F3, 00, FF)

(method 3) 

Adjustment mode: Three modes of Cool, Medium(Vivid) and
Warm

- Equipment : 1) Color analyzer(CA100+, CA210) should be

used in the calibrated ch by CS-1000(PDP :
CH10)

2) Adjustment remocon

- For manual adjustment, it is also possible by the following

sequence.
Operate the zero-calibration of the CA-100+ or CA-210, then
stick sensor to the module when adjusting.

(1) Select white pattern of heat-run by pressing “POWER ON”

key on remote control for adjustment then operate heat run
longer than 5 minutes. (recommend) 
(If not executed this step, the condition for W/B will be
different)

(2) Changing to the AV mode by remote control.(Push front-

AV)

(3) Input external pattern(85% white pattern).
(4) Stick sensor to center of the screen and select each items

(Red/Green/Blue Gain and Offset) using 

D

/

E

(CH +/-) key

on R/C..

(5) Adjust R/ G/ B Gain using 

F

/

G

(VOL +/-) key on R/C.

(6) Adjust three modes of Cool, Medium(Vivid) and Warm as

below figure.
(Fix the one of R/G/B and change the others)
- Push the “VOL + “ key : Cool, Medium, Warm

[

Refer to the below case to know what value is fixed.

[CASE]
First adjust the coordinate much away from the target value(x, y).

1. x, y > target

1) Decrease the R, G. 

2. x, y < target

1) First decrease the B gain, 
2) Decrease the one of the others.

- In case of decreasing the x, decreasing the R : fix G
- In case of decreasing the y , decreasing the G : fix R

3. x > target ,  y < target

1) First decrease B, so make y a little more than the target.
2) Adjust x value by decreasing the R

4. x < target ,  y > target

1) First decrease B, so make x a little more than the target.
2) Adjust x value by decreasing the G

(7) When adjustment is completed, Exit adjustment mode

using EXIT key on R/C.

(For Automatic Adjustment) 

(method 1, using IIC, You connect RGB Cable)

(1) Enter the adjustment mode of the white balance

- Enter the white balance adjustment mode at the same time

heat-run mode when pushing the power on by power only
key

- Maintain the white balance adjustment mode with same

condition of Heat-run 

- Maintain after AC off/on in status of Heat-run pattern display

(2) Release the white balance adjustment mode

- Release the adjust mode after AC off/on or std-by off/on in

status of finishing the Hear-run mode

- push the “power on” key(IIC Mode) on Adjust remote-

controller.

- Release the Adjust mode when receiving the aging off

command(F3 00 00) from adjustment equipment)

(3) Enter the adjust mode of white balance

- Enter the white balance adjustment mode with aging

command(F3, 00, FF)

O

Color Temperature & Color Coordinates Setting

- When adjusting the Color Temperature, Color Analyzer CA-

210(Matrix should be corrected through CH10 of CS-1000)
should be used. When CA-210 have used, it don’t need to fit
the CH10.

- Adjust the Color Temperature based below adjustment color

coordinates.

O

Target Value CA-210(LCD : CH 9, PDP : CH10), CA-100(PDP)

- 14 -

+0.003

6,500K

Warm

+0.000

9,300K

Medium

+0.000

11,000K

Cool

0.276–0.002

0.285–0.002

0.293–0.002

0.329–0.002

0.313–0.002

0.283–0.002

Y

X

uv

Temp

Color coordinate

Mode

Method 1-(I

2

C)