Read LG 50PG3000-ZA (CHASSIS:PD83A) Service Manual online
- 6 -
ADJUSTMENT INSTRUCTION
1. Application Object
These instructions are applied all of the 50” PLASMA TV,
PD83A
PD83A
Chassis.
2. Note
(1) Because this is not a hot chassis, it is not necessary to use
an isolation transformer. However, the use of isolation
transformer will help protect test instrument.
transformer will help protect test instrument.
(2) Adjustment must be done in the correct order.
(3) The adjustment must be performed in the circumstance of
(3) The adjustment must be performed in the circumstance of
25±5°C of temperature and 65±10% of relative humidity if
there is no specific designation.
there is no specific designation.
(4) The input voltage of the receiver must keep 100-240V~,
50/60Hz.
(5) The receiver must be operated for about 15 minutes prior
to the adjustment.
In case of keeping module is in the circumstance of 0°C, it
should be placed in the circumstance of above 15°C for
2hours.
In case of keeping module is in the circumstance of below
-20°C, it should be placed in the circumstance of above
15°C for 3hours.
should be placed in the circumstance of above 15°C for
2hours.
In case of keeping module is in the circumstance of below
-20°C, it should be placed in the circumstance of above
15°C for 3hours.
O
After RGB Full white HEAT-RUN Mode, the receiver must
be operated prior to adjustment.
O
Enter into HEAT-RUN MODE
1) Press the POWER ON KEY on R/C for adjustment.
2) OSD display and screen display PATTERN MODE.
2) OSD display and screen display PATTERN MODE.
* Set is activated HEAT-RUN without signal generator in
this mode.
* Single color pattern(RED/BLUE/GREEN) of HEAT-RUN
mode uses to check PANEL.
3. ADC Calibration
V
Auto adjustment Map(RS-232C)
- Baud : 115200bps, RS232 Host : PC, Echo : none.
4. ADC adjustment
5. Adjustment of RGB
5-1. Auto RGB Gain / Offset Adjustment
(1) Convert to PC in Input-source(refer to I2C command at page 10)
(2) Signal equipment displays
(2) Signal equipment displays
Output Voltage : 700 mVp-p
Impress Resolution XGA(1024x768@60Hz)
Model : 60
Impress Resolution XGA(1024x768@60Hz)
Model : 60
in pattern Generator
Pattern : 65 in pattern Generator(MSPG-925 Series)
[gray pattern that left & right is black and center is white
[gray pattern that left & right is black and center is white
signal(Refer below picture)].
(3) Adjust by commanding AUTO_COLOR_ADJUST.
5-2. Confirmation
(1) We confirm whether “0xAA(RGB)” address of EEPROM
“0xA2” is “0xAA” or not.
(2) If “0xAA(RGB)” address of EEPROM “0xA2” isn’t “0xAA”,
we adjust once more.
(3) We can confirm the ADC values from “0xA4~0xA9(RGB)”
address in a page “0xA2”.
* Manual ADC process using Service Remocon. After enter
Service Mode by pushing “ADJ” key, execute “ADC Adjust”
by pushing “
by pushing “
G
“ key at “ADC CALIBRATION : RGB-C”.
* Using ‘power on’ button off the control R/C, power on TV.
If you turn on a still screen more than 20 minutes, (Especially
digital pattern, cross hatch pattern) after image may be occur in
the black level part of the screen.
digital pattern, cross hatch pattern) after image may be occur in
the black level part of the screen.
ADC adjust
Data Read
Default Write
Enter
Adjust Mode
ADC adjust
ADC Parameter
Digital Data
ADC Parameter
(Average)
Adjustment
Confirmation
Adjust Mode In
Adjust Mode Out
NO
Item
Remark
CMD1 CMD2 Data 0
A
A
A
A
A
A
A
D
D
D
D
D
D
D
0
0
0
0
9
0
0
1
2
3
4
9
0
9
Transfer 18Byte
(Input resolution Data)
To check ADC Adjustment
on Assembly line
When transfer the ‘Mode
In’, Carry the command.
MSPG925FS
Component
RGB-PC
ADC
Model : 60
(1024*768 60Hz)
Pattern : 65
Model : 209(480i 60Hz)
223(1080i 60Hz)
Pattern : 65
(Fig.1)
Click on the first or last page to see other 50PG3000-ZA (CHASSIS:PD83A) service manuals if exist.