Read LG 50PG2000-ZA (CHASSIS:PD83A) Service Manual online
(2) Confirmation
1) We confirm whether “0xB3 (480i)/0xBC (1080i)” address of
EEPROM “0xA2” is “0xAA” or not.
2) If “0xB3 (480i)/0xBC(1080i)” address of EEPROM “0xA2”
isn’t “0xAA”, we adjust once more
3) We can confirm the ADC values from “0xAD~0XB2
(480i)/0XB6~BB (1080i)” addresses in a page “0xA2”
* Manual ADC process using Service Remocon. After enter
Service Mode by pushing “ADJ’ key, execute “ADC Adjust”
by pushing “
by pushing “
G
” key at “ADC CALIBRATION :COMPONENT”.
Caution: Each PCB assembly must be checked by check JIG
set.
(Because power PCB Assembly damages to PDP
Module, especially be careful)
(Because power PCB Assembly damages to PDP
Module, especially be careful)
5. POWER PCB Assembly Voltage
Adjustment
(Va, Vs voltage Adjustment)
5-1. Test Equipment:
D.M.M 1EA
5-2. Connection Diagram for Measuring:
Refer to fig.1
5-3. Adjustment Method
Before Voltage ADJ, do HEAT RUN on 100% Full White
Pattern. (or RF(ATV) Noise Pattern)
(1) 42” EAY39333001 Va Adjustment (refer fig.1)
1) Connect + terminal of D. M..M. to Va pin of P811, connect -
terminal to GND pin of P811.
2) After turning VR901,voltage of D.M.M adjustment as same
as Va voltage which on label of panel right/top (deviation;
±0.5V)
±0.5V)
(2) 42” EAY39333001 Vs Adjustment (refer fig.1)
1) Connect + terminal of D. M..M. to Vs pin of P811, connect -
terminal to GND pin of P811.
2) After turning VR951, voltage of D.M.M adjustment as same
as Vs voltage which on label of panel right/top (deviation ;
±0.5V)
±0.5V)
(3) 50” EAY39190301 Va Adjustment (refer fig.1)
1) Connect + terminal of D. M.M. to Va pin of P811, connect -
terminal to GND pin of P811.
2) After turning VR901,voltage of D.M.M adjustment as same
as Va voltage which on label of panel right/top (deviation;
±0.5V)
±0.5V)
(4) 50” EAY39190301 Vs Adjustment (refer fig.1)
1) Connect + terminal of D. M..M. to Vs pin of P811, connect
-terminal to GND pin of P811.
2) After turning VR951, voltage of D.M.M adjustment as same
as Vs voltage which on label of panel right/top (deviation ;
±0.5V)
±0.5V)
(5) 42” EAY43509401 Va Adjustment (refer fig.1)
1) Connect + terminal of D. M.M. to Va pin of P11, connect -
terminal to GND pin of P11.
2) After turning VR951,voltage of D.M.M adjustment as same
as Va voltage which on label of panel right/top (deviation;
±0.5V)
±0.5V)
(6) 42” EAY43509401 Vs Adjustment (refer fig.1)
1) Connect + terminal of D. M..M. to Vs pin of P11, connect -
terminal to GND pin of P11.
2) After turning VR901, voltage of D.M.M adjustment as same
as Vs voltage which on label of panel right/top (deviation ;
±0.5V)
±0.5V)
(7) 60” EAY41410101 Vs Adjustment (refer fig.1)
1) Connect + terminal of D. M.M. to Va pin of P816, connect -
terminal to GND pin of P816.
2) After turning VR901,voltage of D.M.M adjustment as same
as Va voltage which on label of panel right/top (deviation;
±0.5V)
±0.5V)
(8) 60” EAY41410101 Vs adjustment (refer fig.1)
1) Connect + terminal of D. M..M. to Vs pin of P816, connect -
terminal to GND pin of P816.
2) After turning VR951, voltage of D.M.M adjustment as same
as Vs voltage which on label of panel right/top (deviation ;
±0.5V)
±0.5V)
- 8 -
<42 inch EAY39333001>
<42 inch EAY43509401>
Click on the first or last page to see other 50PG2000-ZA (CHASSIS:PD83A) service manuals if exist.