Read LG 50PC1R-ZH (CHASSIS:PP62A) Service Manual online
- 15 -
8-5. Sequence of Adjustment
1) Init the data.
2) Load the EDID data.( Open File : Analog ,Digital)
2) Load the EDID data.( Open File : Analog ,Digital)
3) Push the “Write Data & Verify” button. And confirm “Yes”.
4) If the writing is finished, you will see the “OK’ message.
5) It is important that PP62C has two HDMI so digital DDC
4) If the writing is finished, you will see the “OK’ message.
5) It is important that PP62C has two HDMI so digital DDC
downloading must be performed two times.(HDMI 1 , HDMI 2)
9. Adjustment of White Balance
9-1. Required Equipment
1) Remote controller for adjustment.
2) Color Analyzer.(CA-100 or same product)
3) Auto W/B adjustment instrument.(only for Auto adjustment)
4) AV Pattern Generator.
2) Color Analyzer.(CA-100 or same product)
3) Auto W/B adjustment instrument.(only for Auto adjustment)
4) AV Pattern Generator.
9-2. Connecting diagram of equipment for
measuring (For Auto Adjustment)
9-3. Adjustment of White Balance
(For Manual adjustment)
O
Operate the zero-calibration of the CA-100, then stick
sensor to PDP module surface when you adjust.
O
For manual adjustment, it is also possible by the following
sequence.
1) Select white pattern of heat-run mode by pressing power on
key on remote control for adjustment then operate heat run
more than 15 minutes.
more than 15 minutes.
2) As below Fig. 10, Supply 216Level (85 IRE) full screen
pattern to Video input.
If Assy has Scart jack ,Use AV3
Else use AV1.
If Assy has Scart jack ,Use AV3
Else use AV1.
3) Enter the White Balance adjustment mode by pressing the
INSTART key twice(White Balance) on R/C.
4) Stick sensor to center of the screen and select each items
(Red/Green/Blue Gain and Offset) using
D
/
E
(CH +/-) key
on R/C.
5) Adjust Only High Light with R Gain / B Gain using
F
/
G
(VOL+/-) key on R/C.
6) Adjust it until color coordination becomes as below.
Initially, R/G/B gain and R/G/B offset values are fixed as below
Red Gain : 82, Green Gain : 80, Blue Gain : 86
Red Offset : 80, Green Offset : 80, Blue Offset : 8C (XGA)
Red Offset : 80, Green Offset : 80, Blue Offset : 89 (VGA)
Red Offset : 80, Green Offset : 80, Blue Offset : 8C (XGA)
Red Offset : 80, Green Offset : 80, Blue Offset : 89 (VGA)
V
Desired result
Brightness :
High Light :
80 ± 20cd/m2
Color-Coordinate :
High Light :
X : 0.283 ± 0.002
Y : 0.298 ± 0.002
Y : 0.298 ± 0.002
Color Temperature : 9,300°K ± 500°K
7) When adjustment is completed, Exit adjustment mode
using EXIT key on R/C.
using EXIT key on R/C.
10. Input the Shipping Option Data
1) Push the IN-START key in a Adjust Remocon.
2) Input the Option Number that was specified in the BOM, into
2) Input the Option Number that was specified in the BOM, into
the Shipping area.
3) The work is finished, Push
V
Key.
11. Default value in adjustment mode
11-1. Auto Color Balance (Component/RGB)
(Fig. 10) Pattern for Adjustment of White Balance
216 Level (85 IRE)
216 Level (85 IRE)
M SPG-
M STG- 5 2 0 0
216 Level (85 IRE)
COLOR
COLOR ANAL
ANALYZER
YZER
TYPE ; CA-100
TYPE ; CA-100
CVBS
CVBS
signal
signal
signal
input
input
input
RS-232C Serial Communication
925
Pattern Generator
/
(Fig. 11) Default Value on OSD
(Fig. 9) Connection Diagram of Auto W/B Adjustment
Click on the first or last page to see other 50PC1R-ZH (CHASSIS:PP62A) service manuals if exist.