47SL9000-ZA, 47SL9500-ZB (CHASSIS:LD91L) - LG TV Service Manual (repair manual). Page 11

· W/B Equipment condition

CA210 : CH 14(LED), Test signal : Inner pattern (85IRE)

· Above 5 minutes H/run in the inner pattern. (“power on” key

of adjust remote control)

* Connecting picture of the measuring instrument

(On Automatic control)
Inside PATTERN is used when W/B is controlled. Connect to
auto controller or push Adjustment R/C POWER ON ->
Enter the mode of White-Balance, the pattern will come out

* Auto-control interface and directions

1) Adjust in the place where the influx of light like floodlight

around is blocked. (illumination is less than 10 lux).

2) Adhere closely the Color Analyzer (CA210) to the module

less than 10cm distance, keep it with the surface of the
Module and Color Analyzer’s Prove vertically.(80~100°).

3) Aging time

- After aging start, keep the power on (no suspension of

power supply) and heat-run over 15minutes.

- Using ‘no signal’ or ‘full white pattern’ or the others,

check the back light on.

• Auto adjustment Map(RS-232C)

RS-232C COMMAND
[CMD Format]
START 6E A 50 A LEN A 03 A CMD A 00 A VAL A CS A STOP

- LEN : Number of Data Byte to be send
- CMD : Command
- VAL : FOS Data
- CS : Checksum of sent Data
- A : Acknowledge
Ex) [Send : JA_00_DD] / [Ack : A_00_okDDX]

[CMD

ID DATA]

Wb

00

00

White Balance Start

Wb

00

ff

White Balance End

In the SET applied LED module, as to physical characteristics
of LED Module, the sets takes a 120 minutes by aging time to
stabilize a color coordinates. So White Balance Control
equipments get the SET Aging Time from SET and then going
to control the W/B by revise color coordinates in the each time

Cautions) The Time Table of color coordinates by SET Aging Time

** Caution **
Color Temperature : COOL, Medium, Warm. 
One of R Gain/ G Gain/ B Gain should be kept on 0xC0, and
adjust other two lower than C0.
(when R/G/B Gain are all C0, it is the FULL Dynamic Range
of Module)

* Manual W/B process using adjusts Remote control.

Dynamic contrast : off
Dynamic color : off
OPC : off
Energy saving mode : off
• After enter Service Mode by pushing “ADJ” key,
• Enter White Balance by pushing “

G

” key at “3. White

Balance”.

- In the SET applied LED module, as to physical

characteristics of LED Module, the sets takes a 120
minutes by aging time to stabilize a color coordinates. So
White Balance Control equipments get the SET Aging Time
from SET and then going to control the W/B by revise color
coordinates in the each time

- 11 -

Cool 13,000k ºK

X=0.269(±0.002)

Y=0.273(±0.002)

<Test Signal>

Medium

9,300k

ºK

X=0.285(±0.002)

Inner pattern

Y=0.293(±0.002)

(216gray,85IRE)

Warm

6,500k

ºK

X=0.313(±0.002)

Y=0.329(±0.002)

Full White Pattern

COLOR
ANALYZER
TYPE: CA-210

RS-232C Communication

CA-210

RS-232C COMMAND MIN

CENTER

MAX

[CMD ID DATA]

(DEFAULT)

Cool

Mid

Warm

Cool

Mid

Warm

R Gain

jg

Ja

jd

00

172

192

192

255

G Gain

jh

Jb

je

00

172

192

192

255

B Gain

ji

Jc 

jf

00

192

192

172

255

R Cut

64

64

64

128

G Cut

64

64

64

128

B Cut

64

64

64

128

H/R Time

Cool

Medium

Warm

(Min)

X

Y

X

Y

X

Y

269

273

285

293

313

329

1

~5

281

297

290

307

318

343

2

6~20

280

288

289

301

317

338

3

21~30

278

285

287

297

316

334

4

31~

276

283

285

293

313

329