47LE5300, 47LE5310 (CHASSIS:LB01D) - LG TV Service Manual (repair manual). Page 11

· W/B Equipment condition

CA210 : CH 9, Test signal : Inner pattern (85IRE)

· Above 5 minutes H/run in the inner pattern. (“power on” key

of adjust remote control)

· Edge LED W/B Table is process of time(Only LGD)

CA210 : CH 14, Test signal : Inner pattern (85 IRE)

* Connecting picture of the measuring instrument

(On Automatic control)

Inside PATTERN is used when W/B is controlled. Connect to
auto controller or push Adjustment R/C POWER ON ->
Enter the mode of White-Balance, the pattern will come out.

* Auto-control interface and directions

1) Adjust in the place where the influx of light like floodlight

around is blocked. (illumination is less than 10 lux).

2) Adhere closely the Color Analyzer (CA210) to the module

less than 10 cm distance, keep it with the surface of the
Module and Color Analyzer’s prove vertically.(80° ~ 100°).

3) Aging time

- After aging start, keep the power on (no suspension of

power supply) and heat-run over 5 minutes.

- Using ‘no signal’ or ‘full white pattern’ or the others,

check the back light on.

• Auto adjustment Map(RS-232C)

RS-232C COMMAND
[CMD

ID DATA]

Wb

00

00

White Balance Start

Wb

00

ff

White Balance End

<Caution>

Color Temperature : COOL, Medium, Warm. 
One of R Gain/G Gain/ B Gain should be kept on 0xC0, and
adjust other two lower than C0.
(when R/G/B Gain are all C0, it is the FULL Dynamic Range
of Module)

* Manual W/B process using adjusts Remote control.

• After enter Service Mode by pushing “ADJ” key,
• Enter White Balance by pushing “

G

” key at “6. White

Balance”.

* After done all adjustments, Press “In-start” button and

compare Tool option and Area option value with its BOM, if
it is correctly same then unplug the AC cable. If it is not
same, then correct it same with BOM and unplug AC cable.
For correct it to the model’s module from factory Jig model.

* Push the “IN STOP” key after completing the function

inspection. And Mechanical Power Switch must be set “ON”.

• Connect D-sub Signal Cable to D-sub Jack.
• Write EDID Data to EEPROM(24C02) by using DDC2B

protocol.

• Check whether written EDID data is correct or not.
* For SVC main Assembly, EDID have to be downloaded to

Insert Process in advance.

• Connect HDMI Signal Cable to HDMI Jack.
• Write EDID data to EEPROM(24C02) by using DDC2B protocol.
• Check whether written EDID data is correct or not.
* For SVC main Assembly, EDID have to be downloaded to

Insert Process in advance.

1) All Data : HEXA Value
2) Changeable Data :
*: Serial No : Controlled / Data:01
**: Month : Controlled / Data:00
***:Year : Controlled
****:Check sum

- 11 -

Cool 13,000

K

X=0.269(±0.002)

Y=0.273(±0.002)

<Test Signal>

Medium

9,300

K

X=0.285(±0.002)

Inner pattern

Y=0.293(±0.002)

(216 gray,85 IRE)

Warm

6,500

K

X=0.313(±0.002)

Y=0.329(±0.002)

 

Full White Pattern

COLOR
ANALYZER
TYPE: CA-210

RS-232C Communication

CA-210

RS-232C COMMAND

MIN

CENTER

MAX

[CMD ID DATA]

(DEFAULT)

Cool

Mid

Warm

Cool

Mid

Warm

R Gain

jg 

Ja 

jd 

00

172 

192 

192

192

G Gain 

jh 

Jb

je 

00

172 

192 

192

192

B Gain 

ji 

Jc 

jf

00

192 

192 

172 

192

R Cut 

64 

64 

64 

128

G Cut 

64 

64 

64 

128

B Cut 

64 

64 

64 

128

Time

Cool

Medium

Warm

X

Y

X

Y

X

Y

0-2 Minute

276

285

292

305

315

334

3-5 Minute

274

282

290

302

313

332

Color

6-9 Minute

273

280

289

300

312

330

Temperature 10-19 Minute

272

278

288

298

311

328

20-35 Minute

271

276

287

296

310

326

36-49 Minute

269

274

286

294

309

324

50-79 Minute

269

273

286

293

308

323

More than 80 Minute

269

273

285

293

308

323