42PG61UR-TA (CHASSIS:PP81A) - LG TV Service Manual (repair manual). Page 13

- 13 -

Adjustment mode: Two modes of Medium(Vivid) and Warm
(Cool data is automatically calibrated by the Medium data)

- Equipment : 1) Color analyzer(CA100+, CA210) should be

used in the calibrated ch by CS-1000(.(LCD :
CH9, PDP : CH10)

2) Adjustment remocon

-  For  manual  adjustment,  it  is  also  possible  by  the  following

sequence.
Operate the zero-calibration of the CA-100+ or CA-210, then
stick sensor to the module when adjusting.

(1) Select white pattern of heat-run by pressing “POWER ON”

key on remote control for adjustment then operate heat run
longer than 15 minutes. (recommend) 
(If  not  executed  this  step,  the  condition  for  W/B  will  be
different)

(2)  Changing  to  the  AV  mode  by  remote  control.(Push  front-

AV)

(3) Input external pattern(85% white pattern).
(4) Stick sensor to center of the screen and select each items

(Red/Green/Blue  Gain  and  Offset)  using 

D

/

E

(CH  +/-)  key

on R/C..

(5) Adjust R/ G/B Gain using 

F

/

G

(VOL +/-) key on R/C.

(6)  Adjust  two  modes  of  Medium(Vivid)  and  Warm  as  below

figure.
(Fix the one of R/G/B and change the others)
1) Default : Medium(Vivid)
2) Push the “VOL +” key twice : Warm

[ Refer to the below case to know what value is fixed.

[CASE]
First adjust the coordinate much away from the target value(x, y).

1. x, y > target

1) Decrease the R, G. 

2. x, y < target

1) First decrease the B gain, 
2) Decrease the one of the others.

- In case of decreasing the x, decreasing the R : fix G
- In case of decreasing the y , decreasing the G : fix R

3. x > target ,  y < target

1) First decrease B, so make y a little more than the target.
2) Adjust x value by decreasing the R

4. x < target ,  y > target

1) First decrease B, so make x a little more than the target.
2) Adjust x value by decreasing the G

(7)  When  adjustment  is  completed,  Exit  adjustment  mode

using EXIT key on R/C.

Caution: Each PCB assembly must be checked by check JIG set.

(Because  power  PCB  Assembly  damages  to  PDP
Module, especially be careful)

(Va, Vs voltage Adjustment)

D.M.M 1EA

Refer to Fig. 5

1) After receiving 100% Full White Pattern, HEAT RUN.
2)  Connect  +  terminal  of  D.  M..M.  to  Va  pin  of  P812,

connect -terminal to GND pin of P812.

3)  After  turning  VR901,voltage  of  D.M.M  adjustment  as

same  as  Va  voltage  which  on  label  of  panel  right/top
(deviation; ±0.5V)

1)  Connect  +  terminal  of  D.  M..M.  to  Vs  pin  of  P812,

connect -terminal to GND pin of P812.

2)  After  turning  VR951  401,  voltage  of  D.M.M  adjustment

as same as Vs voltage which on label of panel right/top
( deviation ; ±0.5V)

<Fig. 5> Connection Diagram of Power Adjustment for Measuring

Color Coordinate

x

y 

0.293±0.002

0.329±0.002

9,300K

6,500K

0.000

0.003

0.285±0.002

0.313±0.002

MEDIUM

WARM

Mode

Temp

uv