32LS570S, 32LS570T, 32LS575S (CHASSIS:LD22E) - LG TV Service Manual (repair manual). Page 10

Read LG 32LS570S / 32LS570T / 32LS575S (CHASSIS:LD22E) Service Manual online

- 10 -
ADJUSTMENT INSTRUCTION
1. Application Range
This specification sheet is applied to all of the LED LCD TV 
with LD22E chassis.
2. Designation
(1)  Because  this  is  not  a  hot  chassis,  it  is  not  necessary  to 
use an isolation transformer. However, the use of isolation 
transformer will help protect test instrument.
(2) Adjustment must be done in the correct order. 
(3)  The adjustment must be performed in the circumstance of 
25 °C ± 5 °C of temperature and 65 % ± 10 % of relative 
humidity if there is no specific designation. 
(4)  The  input  voltage  of  the  receiver  must  keep AC  100-240 
V~, 50/60 Hz.
(5)  The receiver must be operated for about 5 minutes prior to 
the adjustment when module is in the circumstance of over 
15.
In case of keeping module is in the circumstance of 0 °C, it 
should be placed in the circumstance of above 15 °C for 2 
hours.
In case of keeping module is in the circumstance of below 
-20 °C, it should be placed in the circumstance of above 15 
°C for 3 hours.
[Caution] 
When  still  image  is  displayed  for  a  period  of  20  minutes  or 
longer  (Especially  where  W/B  scale  is  strong.  Digital  pattern 
13ch  and/or  Cross  hatch  pattern  09ch),  there  can  some 
afterimage in the black level area.
3. Automatic Adjustment
3.1. ADC Adjustment
3.1.1. Overview
ADC  adjustment  is  needed  to  find  the  optimum  black  level 
and gain in Analog-to-Digital device and to compensate RGB 
deviation.
3.1.2. Equipment & Condition
(1) USB to RS-232C Jig
(2)  MSPG-925  Series  Pattern  Generator(MSPG-925FA, 
pattern - 65)
- Resolution : 1080P Comp1
 
1920*1080 RGB
- Pattern : Horizontal 100% Color Bar Pattern
- Pattern level : 0.7 ± 0.1 Vp-p
- Image
3.1.3. Adjustment
(1) Adjustment method
▪  Don’t need to adjust ADC because there is data in OTP 
and adjusted initially.
▪ Check ADC adjustment
1)  Press  In  start  key  on  the Adj.  Remote  Control,  then 
Adjust ADC(OTP) status is displayed on “1.Adjustment 
check”.  Select  “2.ADC  Data”,  then  ADC  data  is 
displayed.
2)  Press Adj. key on the Adjustmetn Remote Control, and 
select  “9.ADC  Calibration”.  Set  up  the ADC  Type  to 
OTP, then Select [Start] button by pressing Enter key, 
Component and RGB are Writed and display Success 
or NG.
(2) Adj. protocol
Ref.) ADC Adj. RS232C Protocol_Ver1.0
(3) Adj. order
- aa 00 00 [Enter ADC adj. mode]
-  xb 00 04 [Change input source to Component1 (480i& 
1080p)]
- ad 00 10 [Adjust 480i&1080p Comp1]
- xb 00 06 [Change input source to RGB(1024*768)]
- ad 00 10 [Adjust 1920*1080 RGB]
- ad 00 90 End adj.
Protocol
Command
Set ACK
Enter adj. mode
aa 00 00
a 00 OK00x
Source change
xb 00 04
b 00 OK04x (Adjust 480i, 1080p Comp1 )
xb 00 06
b 00 OK06x (Adjust 1920*1080 RGB)
Begin adj.
ad 00 10
Return adj. result
OKx (Case of Success)
NGx (Case of Fail)
Read adj. data
(main)
ad 00 20
(main)
000000000000000000000000007c007b006dx
(sub )
(Sub)
000000070000000000000000007c00830077x
ad 00 21
Confirm adj.
ad 00 99
NG 03 00x (Fail)
NG 03 01x (Fail)
NG 03 02x (Fail)
OK 03 03x (Success)
End adj.
aa 00 90
a 00 OK90x
Page of 119
Display

Click on the first or last page to see other 32LS570S / 32LS570T / 32LS575S (CHASSIS:LD22E) service manuals if exist.