32LP360H (CHASSIS:LB3AC) - LG TV Service Manual (repair manual). Page 12

- 12 -

* CASE Cool

First adjust the coordinate far away from the target value(x, y).
①

 x, y > target

i) Decrease the R, G. 

②

 x, y < target

i) First decrease the B gain, 

ii) Decrease the one of the others.

③

 x > target, y < target

i)  First  decrease  B,  so  make  y  a  little  more  than  the 

target.

ii) Adjust x value by decreasing the R

④

 x < target, y > target

i)  First  decrease  B,  so  make  x  a  little  more  than  the 

target.

ii) Adjust x value by decreasing the G

*  After You finish all adjustments, Press “In-start” button and 

compare Tool option and Area option value with its BOM, if 

it is correctly same then unplug the AC cable.

   If it is not same, then correct it same with BOM and unplug 

AC cable.

  For correct it to the model’s module from factory JIG model.

*  Push  The  “IN  STOP  KEY”  after  completing  the  function 

inspection.

■ Connect D-sub Signal Cable to D-Sub Jack.

■  Write  EDID  DATA  to  EEPROM(24C02)  by  using  DDC2B 

protocol.

■ Check whether written EDID data is correct or not.

*  For Service main Assembly, EDID have to be downloaded to 

Insert Process in advance.

■ Connect HDMI Signal Cable to HDMI Jack.

■  Write  EDID  DATA  to  EEPROM(24C02)  by  using  DDC2B 

protocol.

■ Check whether written EDID data is correct or not.

*  For Service main Assembly, EDID have to be downloaded to 

Insert Process in advance.

(1) All Data : HEXA Value

(2) Changeable Data :

    *: Serial No : Controlled / Data:01

    **: Month : Controlled / Data:00

    ***: Year : Controlled

    ****: Check sum

■ After enter Service Mode by pushing “ADJ” key,

■Enter EDID D/L mode.

■Enter “START” by pushing “OK” key. 

* Caution :  Never  connect  HDMI  &  D-sub  Cable  when  EDID 

downloaded. 

* EDID data and Model option download (RS232)

<Caution>

(1) Use the proper signal cable for EDID Download

* For HDMI EDID(DVI-D to HDMI or HDMI to HDMI Cable)

- Analog EDID : Pin3 exists

- Digital EDID : Pin3 exists

(2) Never connect HDMI & D-sub Cable at the same time.

(3) Use the proper cables below for EDID Writing.

(4)  Download  HDMI1,  HDMI2  separately  because  HDMI1  is 

different from HDMI2.

EZ ADJUST

0. Tool Option1
1. Tool Option2
2. Tool Option3
3. Tool Option4
4. Tool Option5
5. Tool Option Commercial
6. Country Group
7. Area Option
8. ADC Calibration
9. White Balance
10. 10 Point WB
11. Test Pattern

12. EDID D/L 

 

►

13. Sub B/C
14. Ext. Input Adjust

EDID

  HDMI1 

NG

  HDMI2 

NG

  HDMI3 

NG

  RGB 

NG

Start

Reset

EDID

  HDMI1 

OK

  HDMI2 

OK

  HDMI3 

OK

  RGB 

OK

Start

Reset

NO

Item

CMD 1 CMD 2 Data 0

Enter download

MODE

Download

‘Mode In’

A

A

0

0 When transfer the ‘Mode 

In’, Carry the command.

EDID data and

Model option

download

Download

A

E

00 10

Automatically download

(The use of a internal 

data)

For Analog

For HDMI EDID

D-sub to D-sub

DVI-D to HDMI or HDMI to HDMI

No.

Item

Condition

Hex Data

1

Manufacturer ID

GSM

1E6D

2

Version

Digital : 1

01

3

Revision

Digital : 3

03