Read LG 32LH40 / 32LH41 (CHASSIS:LA92B) Service Manual online
6) RGB [C/S: B7FF]
EDID Block 0, Bytes 0-127[00H-7FH], Block Type:EDID1.3
5. Final Assembly adjustment
5.1. White Balance adjustment
5.1.1. Overview
• W/B adjustment : Objective & How-it-works
- Objective: to reduce each Panel’s W/B deviation
- How-it-works: when R/G/B gain in the OSD is at 192, it
- How-it-works: when R/G/B gain in the OSD is at 192, it
means the panel is at its Full Dynamic Range. In order to
prevent saturation of Full Dynamic range and data, one of
R/G/B is fixed at 192, and the other two is lowered to find
the desired value.
prevent saturation of Full Dynamic range and data, one of
R/G/B is fixed at 192, and the other two is lowered to find
the desired value.
5.1.2. Equipment
1) Color Analyzer : CA-210 (NCG: CH 9 / WCG: CH12 /LED
Module:CH14)
2) Adjustment Computer (During auto adj., RS-232C protocol
is needed)
3) Adjustment R/C
4) Video Signal Generator MSPG-925F 720p/216Gray
4) Video Signal Generator MSPG-925F 720p/216Gray
(Model:217, Pattern:78)
-> Only when internal pattern is not available
-> Only when internal pattern is not available
• Color Analyzer Matrix should be calibrated using CS-1000
5.1.3. Equipment connection map
5.1.4. Adjustment Command (Protocol)
• Protocol
<Command Format>
- LEN: Number of Data Byte to be send
- CMD: Command
- VAL: FOS Data
- CS: Checksum of sent Data
- A: Acknowledge
Ex) [Send: JA_00_DD] / [Ack: A_00_okDDX]
- CMD: Command
- VAL: FOS Data
- CS: Checksum of sent Data
- A: Acknowledge
Ex) [Send: JA_00_DD] / [Ack: A_00_okDDX]
• RS-232C Command used during auto-adj.
Ex) wb 00 00 -> Begin white balance auto-adj.
wb 00 10 -> Gain adj.
ja 00 ff -> Adj. data
jb 00 c0
...
...
wb 00 1f -> Gain adj. complete
*(wb 00 20(Start), wb 00 2f(End)) -> Off-set adj.
wb 00 ff -> End white balance auto-adj.
ja 00 ff -> Adj. data
jb 00 c0
...
...
wb 00 1f -> Gain adj. complete
*(wb 00 20(Start), wb 00 2f(End)) -> Off-set adj.
wb 00 ff -> End white balance auto-adj.
• Adj. Map
5.1.5. Adj. method
(1) Auto adj. method
1) Set TV in adj. mode using POWER On Key
2) Zero calibrate probe then place it on the center of the
2) Zero calibrate probe then place it on the center of the
Display
3) Connect Cable(RS-232C)
4) Select mode in adj. Program and begin adj.
5) When adj. is complete (OK Sign), check adj. status per
4) Select mode in adj. Program and begin adj.
5) When adj. is complete (OK Sign), check adj. status per
mode. (Warm, Medium, Cool)
6) Remove probe and RS-232C cable to complete adj.
• Adj. must begin w/ command “wb 00 00”, and end w/“wb
00 ff”and adj. offset if needed.
- 13 -
0
1
2
3
4
5
6
7
8
9
A
B
C
D
E
F
0
00
FF
FF
FF
FF
FF
FF
00
1E
6D
02
00
01
01
01
01
10
00
13
01
03
68
73
41
78
0A
CF
74
A3
57
4C
B0
23
20
09
48
4C
A1
08
00
A9
40
81
80
61
40
45
40
31
40
30
01
01
01
01
01
01
02
3A
80
18
71
38
2D
40
58
2C
40
45
00
7E
8A
42
00
00
1E
01
1D
00
72
51
D0
1E
20
50
6E
28
55
00
7E
8A
42
00
00
1E
00
00
00
FD
00
39
60
3F
1F
52
10
00
0A
20
20
20
20
20
20
00
00
00
FC
70
00
4C
47
20
54
56
0A
20
20
20
20
20
20
20
00
37
Co lo r An alyzer
Co m p ut er
Pat t ern Gen erat o r
RS -232C
RS -232C
RS -232C
Probe
Signal Source
* If TV internal pattern is used, not needed
START 6E A 50 A
LEN A 03 A
CMD A 00 A
VAL A CS A
STOP
CMD
ID
DATA
Explanation
wb
00
00
Begin White Balance adj.
wb
00
ff
End White Balance adj.
(internal pattern disappears)
ITEM
Command
Data Range
Default
(Hex.)
(Decimal)
Cmd 1
Cmd 2
Min
Max
Cool
R-Gain
j
g
00
C0
G-Gain
j
h
00
C0
B-Gain
j
i
00
C0
R-Cut
G-Cut
B-Cut
Medium
R-Gain
j
a
00
C0
G-Gain
j
b
00
C0
B-Gain
j
c
00
C0
R-Cut
G-Cut
B-Cut
Warm
R-Gain
j
d
00
C0
G-Gain
j
e
00
C0
B-Gain
j
f
00
C0
R-Cut
G-Cut
Click on the first or last page to see other 32LH40 / 32LH41 (CHASSIS:LA92B) service manuals if exist.