Read LG 32LD650 (CHASSIS:LT03B) Service Manual online
- 11 -
4.6. Check SW Version
4.6.1. Method
1) Push In-star key on Adjust remote-controller.
2) SW Version check
2) SW Version check
5. SET assembly adjustment method
5.1. Input Area-Option
5.1.1. Profile : Must be changed the Area option
value because being different of
each Country’s Language and
signal Condition.
each Country’s Language and
signal Condition.
5.1.2. Equipment : adjustment remote control.
5.1.3. Adjustment method
- The input methods are same as other chassis.(Use IN-
START Key on the Adjust Remocon.)
Refer to Job Expression of each main chassis ass’y
(EBTxxxxxxxx) for Option value.
(EBTxxxxxxxx) for Option value.
5.2. Adjustment of White Balance : (For
Automatic Adjustment)
A
Purpose : Adjust the color temperature to reduce the
deviation of the module color temperature.
A
Principle : To adjust the white balance without the
saturation,
Fix the one of R/G/B gain to 192 (default data)
and decrease the others.
and decrease the others.
A
Adjustment mode : Three modes – Cool / Medium / Warm
* Required Equipment
A
Remote controller for adjustment
A
Color Analyzer : CA100+ or CA-210 or same product
(should be used in the calibrated ch by CS-1000)
(should be used in the calibrated ch by CS-1000)
• LCD TV : CH-9
• PDP TV : CH-10
• White LED TV : CH-14
• RGB LED(MNT) : CH-16
• PDP TV : CH-10
• White LED TV : CH-14
• RGB LED(MNT) : CH-16
A
Auto W/B adjustment instrument(only for Auto adjustment)
5.2.1. Adjustment of White Balance : (For Automatic
Adjustment)
Connecting diagram of equipment for measuring (For
Automatic Adjustment)
Automatic Adjustment)
1) Set TV in adj. mode using POWER ON key
2) Zero calibrate probe then place it on the center of the
Display
3) Connect Cable(RS-232C)
4) Select mode in adj. Program and begin adj.
5) When adj. is complete (OK Sing), check adj. status pre
mode(Warm, Medium, Cool)
6) Remove probe and RS-232C cable to complete adj.
2) Zero calibrate probe then place it on the center of the
Display
3) Connect Cable(RS-232C)
4) Select mode in adj. Program and begin adj.
5) When adj. is complete (OK Sing), check adj. status pre
mode(Warm, Medium, Cool)
6) Remove probe and RS-232C cable to complete adj.
• W/B Adj. must begin as start command “wb 00 00” , and
finish as end command “wb 00 ff”, and Adj. offset if need
finish as end command “wb 00 ff”, and Adj. offset if need
* Luminance min value is 150cd in the Cool/Medium/Warm
mode( For LCD)
IN START
Model Name : Global-Plat
1.Adjust Check
¢”
¢”
Adjust Check
Serial Number : SKJY1107
2.ADC Date
1. Country Group
(Press OK to Save)
S/W Version
: 00.00.06.01
3.Power Off Status
Country Group Code
MICOM Version
: 2.00.2
4.System
Country Group
BOOT Version
: 1.01.01
5.Model Number D/L
Country
URSA Version
: 1.00
6.Test Option
2. Tool Option
IR LED Version
: ff
7.External ADC
Tool Option1
EDID Version(RGB)
: 0.01
8.Bluetooth Test
Tool Option2
EDID Version(HDMI)
: 0.02
9.Bluetooth AV CODEC Config
Tool Option3
Maker
: 99
10.Spread Spectrum
Tool Option4
BT S/W Version
: 1.21
11.Sync Level
Tool Option5
BT H/W Version
: 4384
12.Wireless Ready
3. Adjust White Balance :
OK
Wireless Host Version
: 0.00.0
13.Stable Count
4. Adjust ADC :
OK
Wireless B/B Version
: 0.00.0
480i Component
MAC Address : FF:FF:FF:FF:FF:FF
1080p Component
RGB
5.EDID :
OK
RGB
HDMI1
HDMI2
HDMI3
UTT : 9
UI Res. Version : 1.06
APP History Ver. : xxxxx
HDMI4
11
A-CAS
-
16672
OK
OK
OK
OK
OK
OK
OK(0x1C)
OK(0xD6,0xF9)
OK(0xD6,0xF9)
OK(0xD6,0xF9)
OK(0xD6,0xF9)
OK(0x1C)
OK(0xD6,0xF9)
OK(0xD6,0xF9)
OK(0xD6,0xF9)
OK(0xD6,0xF9)
Co lo r An alyzer
Co m p ut er
Pat t ern Gen erat o r
RS -232C
RS -232C
RS -232C
Probe
Signal Source
* If TV internal pattern is used, not needed
Click on the first or last page to see other 32LD650 (CHASSIS:LT03B) service manuals if exist.