Read LG 32LC41 / 32LC42 / 32LC43 / 32LC44 / 32LC4R (CHASSIS:LP78A) Service Manual online
- 16 -
(3) DDC adjustment support command set
6.3. Adjustment of White Balance
(For Manual adjustment)
- Operate the zero-calibration of the CA-110 or CA-210, then
stick sensor to LCD module when you adjust.
- For manual adjustment, it is also possible by the following
sequence
1) Select RF no signal by pressing “POWER ON” key on
remote control for adjustment then operate heat run
more than 15 minutes.
(If not executed this step, the condition for W/B will be
differ. The W/B condition is Picture Mode : Standard
(MA : Optimum), Color Temp : Normal. )
more than 15 minutes.
(If not executed this step, the condition for W/B will be
differ. The W/B condition is Picture Mode : Standard
(MA : Optimum), Color Temp : Normal. )
2) Changing to the av mode by pushing the input or front av
key.
3) Display the internal pattern of the VCT-Pro IC by
pushing the IN-START.
4) Stick sensor to center of the screen and select each
items (Red/Green/Blue Gain and Offset) using
D
/
E
(CH+/-) key on R/C.
5) Adjust R Gain / B Gain using
F
/
G
(VOL+/-) key on R/C.
6) Adjust it until color coordination becomes as below.
(Initially, R/G/B gain and R/G/B offset values are fixed
as below)
as below)
Red Gain : 80 , Green Gain : 80 , Blue Gain : 80
Red Offset : 80, Green Offset : 80 , Blue Offset : 80
Red Offset : 80, Green Offset : 80 , Blue Offset : 80
* Target Value [Picture Mode : Standard (ZA, TA),
Optimum(MA), Color Temp: Normal]
-Normal (9300K) x ; 0.283±0.003 y ; 0.298±0.003
-Luminance(Y) AV : upper 150 cd/m
-Luminance(Y) AV : upper 150 cd/m
2
(Typ : 350 cd/m
2
≥)
=> Reference Value(Automatically fixed)
- Cool(11000K): x:0.274±0.003, y: 0.286±0.003
- Warm(7200K) : x:0.303±0.003, y: 0.319±0.003
- Warm(7200K) : x:0.303±0.003, y: 0.319±0.003
<Pattern for Adjustment of White Balance>
7) When adjustment is completed, Exit adjustment mode
using EXIT key on R/C
6.4. Input the Shipping Option Data
1) Push the ADJ key in a Adjust Remote control.
2) Input the Option Number that was specified in the BOM,
2) Input the Option Number that was specified in the BOM,
into the Shipping area.
3) The work is finished, Push
A
Key.
7. Default Value in Adjustment mode
(Default values maybe modified the module condition)
7.1. White Balance
<Default Value on OSD>
9. Sound spec.
Adjustment
Aging On/Off
Input select
R GAIN
G GAIN
B GAIN
CMD(HEX)
F3
F4
16
18
1A
ADR
00
00
00
00
00
FF : ON / OO : OFF
0x10 : TV
0x20 : AV1(SCART1)
0x21 : AV2(SCART2)
0x23 : AV3(Side AV)
0x40 : Component1
0x50 : RGB DTV
0x60 : RGB PC
0x90 : HDMI1 DTV
GAIN adjustment
Item
Dielectric Voltage (AC <-> FG)
Dielectric Voltage (Without FG)
Value
1.5
3
Unit
kV
kV
Remark
At 100mA for 1sec (Line)
At 100mA for 1min (OQC)
At 100mA for 1sec (Line)
At 100mA for 1min (OQC)
Item
Min
Typ
Max
Unit
Remark
Audio Practical Max Output, L(Mono)/R
6
7
9
W
LCD
Click on the first or last page to see other 32LC41 / 32LC42 / 32LC43 / 32LC44 / 32LC4R (CHASSIS:LP78A) service manuals if exist.