32LB9D (CHASSIS:LB73B) - LG TV Service Manual (repair manual). Page 12

(For manual adjustment)

: When adjusting the LCD white balance, use CS-1000 as
the color analyzer (CA-210) and channel 9 corrected of
Matrix (corrected for White, Red, Green, Blue) and the
adjustment must be done in accordance with the below
White balance adjustment coordinate.

1) Press the ADJ of adjustment adjustment remote control

to enter ‘EZ-ADJUST’.

2) Select 9.TEST PATTERN using the CH + / - KEY and

press the Enter KEY to execute a heat run for more
than 30 minutes. 

3) Execute a Zero Calibration for CA-210 and put it at

distance of less than 10Cm from the LCD module
surface center during the adjustment. 

4) Press the ADJ of adjustment remote control, select

‘6.White-Balance’ of ‘Ez – Adjust’ and enter the
adjustment mode using the right key (

G

).

(When you press the 

G

button, the screen enters the full

white internal pattern.)

5) The adjustment is executed in 3 different white balance

of COOL, MEDIUM and WARM.

2) In case that White balance is COOL.

- Fix R-Cut/ G-Cut/ B-Cut to 64 and adjust the color

coordinates t downward.

In case that White balance is Medium.
- Fix R-Cut/ G-Cut/ B-Cut to 64 and adjust the color

coordinates t downward.

In case  that White balance is Warm
- Fix R-Cut/ G-Cut/ B-Cut to 64 and adjust the color

coordinates t downward.

- Adjust by using Vol ± key.

4) When the adjustment is completed, press the OK (

A

)

key button to move to the Ez –Adjust screen. Press the
ADJ KEY to exit the adjustment mode.

* Note : White Balance adjustment coordinate and white balance

1) Standard white balance standard white balance

coordinate when using CS-1000 device
COOL : T=11000K, Δuv=0.000, x=0.276, y=0.283
MEDIUM : T=9300K, Δuv=0.000, x=0.285, y=0.293
WARM : T=6500K, Δuv=0.000, x=0.313, y=0.329

2) Directed color coordinate when using CA-210 CH 9

* Brightness: Full white 216gray 

This is a adjustment to reduce the color difference of RF,
video signal.

1) Connect the Video Signal Generator (Master) to TV AV

input terminal with AV output. At this time, when you enter
the input pattern as Model : 202(PAL), Pattern : 33(100%
color Bar), the following video is displayed on the screen.

* Because the above pattern can differ by the model and

pattern for each device, you must check the pattern first.

2) When the receiving signal is confirmed after inputting the

internal signal, press the ADJ key on the adjustment
remote control to enter ‘EZ-ADJUST’. Select ‘3.Adjust RF
and Video’ and press the right key (

G

) to enter the

adjustment mode.

3) When you enter the adjustment mode, the video is

automatically set to TV 3CH and the following window is
displayed.

4) When the adjustment is completed, a message saying ‘RF

Configuration Success’ is displayed. If the adjustment has
failed, a message saying ‘RF Configuration Fail’ is
displayed.

5) When the automatic adjustment of RF signal is completed,

it is automatically switched to the AV1 Mode, and
automatic adjustment for Video Mode is done. When the
automatic adjustment is completed, a message saying ‘AV-
PAL Configuration Success’ is displayed. If the adjustment
has failed, a message saying ‘AV-PAL Configuration Fail’
is displayed.

- 12 -

Color temperature

Color analyzer

Color coordinate

X

Y

COOL

CA-210

0.276 ± 0.002

0.283 ± 0.002

MEDIUM

CA-210

0.285 ± 0.002

0.293 ± 0.002

WARM

CA-210

0.313 ± 0.002

0.329 ± 0.002

<Fig 5> Model : 202(PAL), Pattern 33(100% color Bar)

 

<Fig 6>