32HIZ22 (CHASSIS:LP62F) (serv.man2) - LG TV Service Manual (repair manual). Page 12

- 12 -

* Caution : System control RS-232C Host should be “PC” for

adjustment

- Press the FRONT-AV KEY on remote control for converting

input mode

(Change RS-232C Host : pc, Band Rate : 115200bps)

1) Remote controller for adjustment
2) 802F Pattern Generator, Master (MSPG-925FA), etc.
3) MSPG-925FA Pattern Generator

(Which has Video Signal: 100% Color Bar Pattern
shown in Fig. 1)
=> Model : 202 / Pattern: 33 (PAL : ZH, TH)

Model : 201 / Pattern : 33 (NTSC : MH)

1) Press the FRONT-AV KEY on remote control for

converting input mode.

2) Input the Video Signal: 100% Color Bar signal into

AV3(ZH), AV1(TH), VIDEO1(MH).

3) Set the PSM to Standard mode in the Picture menu.
4) Press INSTART key on remote control for adjustment.
5) Press the 

G

(Vol.+) key to operate the set, then it

becomes automatically.

6) Auto-RGB OK means the adjustment is completed.

1) This AV color balance adjustment should be performed

before White Balance Adjustment.

2) After AV color balance adjustment, Change the mode

from AV to RF. (Cancel Heat-run mode.)

1) Remote controller for adjustment
2) 802F Pattern Generator, Master (MSPG-925FA), etc.
3) MSPG-925FA Pattern Generator 

(Which has 720p YPbPr signal : 100% Color Bar Pattern
shown in Fig. 2 )
=> Model: 217 / Pattern: 33

4) It is very import to use correct adjustment pattern like Fig.1.

- Within the pattern, color sequence should be aligned

: White-Yellow-Cyan-Green-Magenta-Red-Blue-Black
(If color sequence is reversed (Black -> ... -> White),
reverse the pattern with REV key, when using Master
pattern generator like MSPG-925)

- If Minimum Black Level and/or Maximum White Level

is not correct, select 100% Color Bar Pattern.

1) Input the Component 720p 100% Color Bar(MSPG-

925FA model:217, pattern:33) signal into Component.
(ZH : component , TH/MH : component 1 or 2)

2) Set the PSM to Standard mode in the Picture menu.
3) Press the INSTART key on remote control for

adjustment.

4) Press the 

G

(Vol. +) key to operate the set , then it

becomes automatically.

5) Auto-RGB OK means the adjustment is completed.

1) Remote controller for adjustment
2) 802F Pattern Generator, Master (MSPG-925FA), etc.
3) MSPG-925FA Pattern Generator

(Which has XGA [1024x768] 60Hz PC Format output
signal : 100% Color Bar Pattern shown in Fig. 1)

4) It is very import to use correct adjustment pattern like Fig.1.

- Within the pattern, color sequence should be aligned.

: White-Yellow-Cyan-Green-Magenta-Red-Blue-Black
(If color sequence is reversed (Black ->...-> White),
reverse the pattern with REV key, when using Master
pattern generator like MSPG-925).

- If Minimum Black Level and/or Maximum White Level

is not correct, Do select 100% Color Bar Pattern.

1) Input the PC 1024x768 @ 60Hz 1/2 Black & White

Pattern (MSPG-925FA model : 3, patter : 3) into RGB.

2) Set the PSM to Standard mode in Picture menu.
3) Press the INSTART key on remote control for adjustment.
4) Press the 

G

(Vol. +) key operate To set , then it becomes

automatically.

5) Auto-RGB OK means adjustment is completed.

Notice : Before White-balance, change input mode.

Move to AV3(ZH) or AV1(TH) or VIDEO1(MH) by using
the FRONT-AV KEY on Remote controller.

<Caution>

- System control RS-232 Host should be "PC" for

adjustment.

- AV ADC(ZH: AV3, TH : AV1, MH: VIDEO1) should be

done before White-balance.

MSPG-

925FA

AV ADC Condition

PAL

NTSC

Input

ZH model:AV3

MH model

-select

TH model:AV1

:VIDEO1

Model:202(PAL-BGDHI)

Model:201(NTSC)

Pattern :33

*100% Color Bar

Component

Model : 217

DVI(RGB)

Model : 3 

(1024x768@6

0Hz)

<Fig. 1>

White balance

ZH(AV3), TH(AV1)

MH(VIDEO1)

MSPG925FA 

216 Level (85IRE)

Model : 202

Model : 201

Full screen pattern

* Pal Video

* NTSC Video