19LV2300 (CHASSIS:LA86D) - LG TV Service Manual (repair manual). Page 14

- 14 -

- Purpose and principle for adjusting the white balance
- Principle: The full dynamic range of the module when the

RGB gain on the OSD is 192. In order to adjust the white
balance with no saturation of the full dynamic range and the
data, fix one of the RGB gains to 192 and decrease the
remaining two gains to adjust

1) Color Analyzer : CA-210 

(NCG: CH 9 / WCG: CH12 / LED Module : CH14)

2) Computer to adjust (needed for the automatic adjustment,

possible to communicate with the RS-232C)

3) Adjustment remote controller
4) Video Signal Generator MSPG-925F 720p/216Gray

(Model:217, Pattern:78)

=> Applied only when the inner pattern cannot be used

*Use the Color Analyzer with the matrix calibrated by the CS-

1000

- "wb 00 00": Start Auto-adjustment of white balance.
- "wb 00 10": Start Gain Adjustment (Inner pattern) 
- "jb 00 c0" : 
- …
- "wb 00 1f": End of Adjustment

* If it needs, offset adjustment (wb 00 20-start, wb 00 2f-

end)

- "wb 00 ff": End of white balance adjustment (inner pattern

disappear)

1) The adjustment condition should be set by the Power On

key.

2) Perform the zero calibration of the Color Analyzer and

place the probe close to the display center.

3) Connect the communication cable (RS-232C).
4) Select the desired model of the adjustment program and

perform the adjustment.

5) After the adjustment is ended (check the OK sign), check

the adjustment condition for each mode of the set.

(Warm, Medium, Cool)

6) Disconnect the probe and the communication cable to end

the adjustment.

* The adjustment should be started with "wb 00 00" and ended

with "wb 00 ff", and the offset should be adjusted when
necessary.

1) The adjustment condition should be set by the Power On

key.

2) Press the ADJ of the R/C to enter into 'EZ-ADJUST'.
3) Select '10.TEST PATTERN' with the CH +/- key and press

the Enter key for 30 minutes or longer to perform the heat
run.

4) Perform the zero calibration of the Color Analyzer and fix

the sensor with the 10cm or less distance at the center of
the LCD module surface when adjusting.

5) Press the ADJ of the R/C to select '7.White-Balance' of the

Ez-Adjust and press the right arrow key(

G

) to enter into

the adjustment mode.

(As soon as you press '

G

', the screen is entered into the

full white inner pattern.)

6) Fix one of the R/G/B gains to 192 and decrease the

remaining two gains to adjust not to exceed 192.

7) The adjustment is done at three white balances of Cool,

Medium and Warm.

* The inner pattern is basically used, and if it is not possible, the

adjustment can be done by selecting the HDMI input. NONE,
INNER or HDMI can be selected by the bottom option at the Ez
Adjust Menu 7.White Balance menu and it is set to INNER as
default. If the adjustment cannot be done by the inner pattern,
select the HDMI to adjust.

* Adjustment environment and reference

1) Environment illuminance

Adjust it to 10 LUX or less at the place where the light
source such as lamp should be blocked at maximum.

2) Probe location

- LCD: Maintain the Color Analyzer (CA-210) close to the

module surface by 10cm or less and keep the probe
of the Color Analyzer perpendicular to the module
surface (80°~ 100°).

3) Aging time

- For the LCD, make sure that the back light is turned on by

using no signal and the full white pattern or others.

RS-232C COMMAND

Meaning

[CMD    ID      DATA]

wb

00

00

White Balance adjustment start.

wb

00

ff

End of White Balance adjust(Inner pattern disappeared