Read LG 17LS5R (CHASSIS:LP68A) Service Manual online
- 10 -
4. Total Assembly line process
4.1. Adjustment Preparation
(1) Above 30 minutes Heat-run in RF no signal
(2)15 Pin D-Sub Jack is connected to the signal of Pattern
(2)15 Pin D-Sub Jack is connected to the signal of Pattern
Generator.
4.2. Confirm color coordinate of AV2
(1) Set Input to AV2.
(2) Input signal : CVBS, PAL @ 50Hz
(2) Input signal : CVBS, PAL @ 50Hz
Full White 216/255 gray level (85 IRE, Model : 202
Patter : 78 at MSPG925L)
Patter : 78 at MSPG925L)
(3) Set PSM : Dynamic / CSM : Cool
(4) Confirm whether x=0.276±0.03, y=0.283±0.03, y≥0.250 or
(4) Confirm whether x=0.276±0.03, y=0.283±0.03, y≥0.250 or
not.
4.3. Other quality
(1) Confirm that each items satisfy under standard condition
that was written product spec..
(2) Confirm Video and Sound at each source.
1) AV
(a) Select input AV1 and check whether picture is
displayed or not. - Check whether SCART output
picture is displayed or not.
picture is displayed or not.
(b) Select input AV2(S-video) and check whether picture
is displayed or not.
(c) Select input AV2(CVBS) and check whether picture
is displayed or not.
2) TV : Select input TV and check below item.(In Gumi factory)
C05(E05) – Check TELETEXT Function (Applicable
to the model that has Teletext code set-
up item in Product spec)
up item in Product spec)
C07(E07) – Check Nicam DUAL
C52 (E52) – Check Nicam Stereo
* Refer to “6.Preset CH information”
C52 (E52) – Check Nicam Stereo
* Refer to “6.Preset CH information”
4.4. Power consumption confirmation
(1) Check if Power LED Color and Power Consumption
operate as standard.
(2) Measurement Condition : 230V~, 50Hz (Analog)
(3) Confirm Stand-by operation.
(3) Confirm Stand-by operation.
4.5. Outgoing condition Configuration
(1) After all function test, press IN-STOP Key by Service
Remote control. And make outgoing condition.
(2) When pressing IN-STOP key by service remote control,
LED is power off in a little time and then automatically LED
is changed the stand-by status(RED Color).(Must not AC
power OFF at that time)
is changed the stand-by status(RED Color).(Must not AC
power OFF at that time)
4.6. Option data setting (SVC OSD setting)
- Tool Option
20LS5R-ZA
REMARK
8 9 6
Resolution
0
Module
0
TV
1
SCART
1
AV2
1
COMPONENT
0
PC-RGB
0
DVI
0
HDMI
0
- Area Option [ A B ]
(A) 0 : FACTORY MODE OFF
1 : FACTORY MODE ON
[Caution] FACTORY MODE ON only used in factory.
(B) 0: default Option setting.
1~4: The other Area Option setting.(Reserved)
[Caution] Initial Setting of Area Option is [1 0] in production line.
After IN-STOP, Area Option will change [0 0].
If Area Option isn
’t 00 after IN-STOP, must change to 00. (Using
G
key on R/C)
No
Item
Condition
Remark
OPTION 1 [6]
1
200PR
0
0 : 200 PR Off
1 : 200 PR On
2
ACMS
1
0 : ACMS Off
1 : ACMS On
3
TEXT
1
0 : TOP
1 : FLOF
4
CH+AU
0
0 : Except below area
1 : China, Australia
5
BOOSTER
0
OPTION 2 [2]
1
SYS
0
0 : BG/I/DK/L
1 : BG/I/DK/M
2
A2 ST
1
Acting FM-ST after checking Nicam
3
I II SAVE
0
0 : I II SAVE Off
1 : I II SAVE On
4
HDEV
0
0 : Except below area
1 : China
5
V-Curve
0
0 : Turbo Volume Off
1 : Turbo Volume On
6
MONO
0
OPTION 3 [2]
1
KEY-TYPE
2
2 : 8Key
OPTION 4 [3]
1
Default Lang
3
2
Lang
0
Chesky Dansk Deutsch English Español Français
Italiano Magyar Nederlands Norsk Polski Português
ΡУССКИЙ Romaneste Suomi Svenska
3
T- Lang
0
AUSTRIA NORWAY BULGARIA POLAND
CROATIA PORTUGAL CZECH RUMANIA
DENMARK RUSSIA ENGLAND SERBIA
ESTONIA SLOVAKIA FINLAND SLOVENIA
FRANCE SPAIN GERMANY SWEDEN
GREECE SWITZERLAND HUNGARY
TURKEY ITALY ARAB LATVIA HEBREW
NETHERLANDS Others
OPTION 5 [9]
1
2HR-OFF
1
0 : 2 Hour off option -OFF
1 : 2 Hour off option -ON
2
TV-LINK-TUNER
0
3
FACTORY-MODE
0
0 : EEPROM Write Protection On
1 : EEPROM Write Protection Off
4
CHANNEL-MUTE
1
0 : Channel Mute Off
1 : Channel Mute On
Click on the first or last page to see other 17LS5R (CHASSIS:LP68A) service manuals if exist.