15LS1R-MG (CHASSIS:CL-81) - LG TV Service Manual (repair manual). Page 9

Read LG 15LS1R-MG (CHASSIS:CL-81) Service Manual online

- 9 -
1. Application
This document is applied to 15", 20" LCD TV which is
manufactured in Monitor Factory or is produced on the basis
of this data. 
2.  Designation
2.1 The adjustment is according to the order which is
designated and which must be followed, according to the
plan which can be changed only on agreeing.
2.2. Power Adjustment: Free Voltage
2.3. Magnetic Field Condition: Nil.
2.4. Input signal Unit: Product Specification Standard  
2.5. Reserve after operation: Above 30 Minutes 
2.6. Adjustment equipments: Pattern Generator (MSPG-925
or Equivalent), DDC Adjustment Jig equipment, SVC
remote controller
3. Adjustment
3.1 APC
After Manual-Insult, executing APC
3.2  ISP UOC file
3.2.1 Required Equipment 
- JIG for ISP
- PC that is installed with  "WISP" program. 
- Control + Power LED PCB Ass'y
3.2.2 ISP Sequence 
1) Connect main board with JIG for ISP
2) Execute "WISP" Program.
3) Compare UOC version in BOM with version of hex file.
4) Push "Browse..." button and select hex file.
5) Push  " Auto Execute" button.
6) Occur an Error, push "Erase" button and try again and
again. 2)~5)
7) After finishing ISP, Must AC off / ON
8) Wait LED is not blink anymore
3.3 ADC Process
"IIC_ SW" must set "0"(After ISP, automatically set "0")
3.3.1 PC input ADC
3.3.1.1 Auto Gain/Offset Adjustment
A
Convert to PC in Input-source
Push "INSTART" in  service  remocon select "Auto
ADC"
A
Signal equipment displays
Output Voltage  :  730  mVp-p
Impress Resolution XGA (1024 x 768 @ 60Hz) 
Pattern : gray pattern that left & right is black and center
is white signal (Refer below picture).
(Model : 37, Pattern : 28 at MSPG925L)
A
Enter SVC menu and select "AUTO ADC" => "AUTO
GAIN" => 
G
After check autocontrol of ADC, push menu key for
exiting SVC Menu.
3.3.1.2 Confirmation
A
We confirm whether "0x00" address of EEPROM
"0xA0" is "0xAA" or not.
A
If "0x00" address of EEPROM "0xA0" isn't "0xAA", we
adjust once more
A
We can confirm the ADC values from "0x06~0x0B"
addresses in a page "0xA0"
3.3.2  AV(CVBS) Mode Adjustment 
3.3.2.1 Auto Gain/Offset Adjustment
A
Select AV(Video) in Input menu
A
Signal equipment : MSPG925
Output Jack : CVBS
Output Voltage : 730  mVp-p (patt # 28 in MSPG925)
Resolution : NTSC J - 720 x 480 @59,94Hz  (Model
#207 in MSPG925)
A
Enter SVC menu and select "AUTO ADC"=>"AUTO
GAIN" => 
G
After check autocontrol of ADC, push menu key for
exiting SVC Menu.
3.3.2.2 Confirmation of adjustment process
A
We confirm whether "0x01" address of EEPROM
"0xA0" is "0xAA" or not. 
A
If "0x01" address of EEPROM "0xA0" isn't "0xAA", we
adjust once more in adjustment line by adjust method
of 3.2.1.2.
A
We can confirm the ADC values from "0x0C~0x11"
addresses in a page "0xA0"
3.3.3 Component Mode Adjustment 
3.3.3.1 Auto Gain/Offset Adjustment
A
Select Component in Input menu 
A
Signal equipment : MSPG925
Output Jack : D4(Japan) or Component(Except Japan)
Output Voltage  :  700  mVp-p (patt # 8 in MSPG925)
Resolution  483/60P  - 720 x 483p @59.94Hz (Model
#212 in MSPG925)
A
Adjust by commanding AUTO_COLOR_ADJUST
(0xF1) 0x00 0x00 instruction.
3.3.3.2 Confirmation of adjustment process
A
We confirm whether "0x01" address of EEPROM
"0xA0" is "0xAA" or not.   
A
If "0x01" address of EEPROM "0xA0" isn't "0xAA", we
adjust once more in adjustment line by adjust method
of 3.2.1.2.
A
We can confirm the ADC values from "0x??~0x??"
addresses in a page "0xA0"
*Caution*
If DDC CMD don't work, please check below.
1. Enter SVC menu by  SVC Remote controller
2. Enter "ETC" menu
Check please,  IIC_SW is "0" or "1".
- IIC_SW  "0" : DDC Communications.(DDC2AB)
- IIC_SW  "1" : EDID Write/Read (DDC2B) and Factory
default.
ADJUSTMENT INSTRUCTION
Page of 28
Display

Click on the first or last page to see other 15LS1R-MG (CHASSIS:CL-81) service manuals if exist.