Read JBL DA 4002 (serv.man3) User Guide / Operation Manual online
• Oversized Floating Rail Mosfet Power
• Fully complementary output stage with
• Power-on indicator badge
mance, we encourage you to read the
remaining pages before installing and
operating your new JBL Decade power
amplifier. Especially review the Appli-
cations section for ideas on designing
and expanding your system. Also, save
these instructions for future reference.
stereo components can require extensive
experience in performing a variety of
electrical and mechanical procedures.
Although these instructions explain how
to install a JBL Decade power amplifier in
a general sense, they do not show the
exact installation methods for your partic-
ular vehicle. If you do not have the expe-
rience, do not attempt the installation
yourself; instead ask your Authorized JBL
Car-Audio Dealer about professional
itor the amplifier and will shut it down if
the electrical system voltage drops
below 5Vdc or exceeds 18Vdc, tempera-
tures are above 194° F (90° C), short cir-
cuits occur or current draw exceeds
product specifications. For best perfor-
mance, check the intended mounting site
to make sure the operating environment
does not create conditions that will trigger
Also disconnect the (–) negative lead
from the vehicle’s battery.
lines and electrical wiring. Use extreme
caution when cutting or drilling in and
around these areas.
drilling any holes or installing any
screws. Remember that mounting
screws can extend behind the mount-
and properly secured. Observe the
polarity markings on the rear panel.
Refer to the application drawings to set
up the amplifier for operation in stereo,
bridged-mono, bi-amp or tri-mode con-
replacement. Do not substitute another
the latest advances in discrete circuit
topology ensuring low distortion and
superbly clean and clear sound quality.
In addition to RCA-type pre-amp inputs,
Decade Series amplifiers feature Floating
Ground Factory-Head-Unit Interface
tory-installed audio systems for distor-
tion-free performance. All JBL Decade
Series power amplifiers feature built-in
electronic crossovers for easy system
expansion without additional outboard
speaker level output from the source
unit (2-channel on DA4002, DA6502,
DA1002; 2 separate 2-channel connec-
tors on DA3504).
channel on DA3504.
DA3504: 30A ATC.
filter @120Hz (HP), a Low-Pass filter
@120Hz (LP) or unfiltered (FLAT). Low-
pass filter frequency selector (DA1002).
barrier strip on the amplifier using at
least 16G high-quality speaker wire.
(Note: The total impedance of the
speakers connected to the outputs
when the amp is driven in stereo must
be at least 2 ohms.)
marked “bridge”, observing proper
polarity. (Note: The total impedance of
the speaker system to be connected to
the amplifier must be at least 4 ohms
in bridge mode.)
one or two pairs of satellite speakers
and a subwoofer), refer to the chart
below to determine the capacitor and
inductor values you’ll need to route
bass signals to the woofer, and
midrange and high frequencies to the
satellite speakers. These passive
crossover components will also ensure
that the impedance of the speaker
system doesn’t drop below 2 ohms.
with output voltage less than 4V, sim-
ply plug the RCA plugs into the RCA
jacks on the amplifier.
source unit that only has speaker-level
outputs, connect the speaker outputs of
the source to the speaker input plug on
the amp using the connector provided.
mounted in virtually any location inside
the vehicle. However, make sure to keep
the amplifier away from heater vents or
1. At the chosen site, use the amplifier
locations of the four mounting holes.
1. For power, remote and speaker wires,
reveal bare wire for insertion into the
barrier strip connectors.
black wire (at least 12G for DA4002,
10G for DA6502, DA1002 and DA3504)
to the Gnd terminal and connect the
other end to the nearest bare-metal
chassis component. Then, connect a
red wire (at least 12G for DA4002, 10G
for DA6502, DA1002 and DA3504) from
the vehicle’s +12-volt battery terminal
to the +Batt terminal on the barrier
strip. Finally connect a blue wire (16G)
to the Rem terminal on the barrier strip
and connect the other end to the Rem
output of the source unit.