Read JBL A302GTi User Guide / Operation Manual online
System Set-Up and Adjustment
Programming and Using the
Status Monitor
In order for the status monitor to
display the correct data, it must be
programmed. Follow the sequence
below after the amplifier(s) has been
installed. Refer to Figure 3 for the
location of the controls.
1. While pressing the Power button,
Status Monitor
In order for the status monitor to
display the correct data, it must be
programmed. Follow the sequence
below after the amplifier(s) has been
installed. Refer to Figure 3 for the
location of the controls.
1. While pressing the Power button,
turn on the head unit.
2. Select the appropriate amplifier
by repeatedly pressing the
“mode” button. A601GTi is
abbreviated as A601. A1201GTi
is abbreviated as A12k, and
A302GTi is abbreviated as A302.
“mode” button. A601GTi is
abbreviated as A601. A1201GTi
is abbreviated as A12k, and
A302GTi is abbreviated as A302.
3. Press “Power” to confirm your
selection. The status monitor will
display “OK”.
display “OK”.
4. Press the “Mode” button to
select a value that most closely
corresponds to the nominal
impedance of the speaker
system connected to your amp.
For the A302GTi, choose the
value that corresponds to the
impedance of either channel.
This information must be correct
in order for the monitor to
correctly calculate output power.
corresponds to the nominal
impedance of the speaker
system connected to your amp.
For the A302GTi, choose the
value that corresponds to the
impedance of either channel.
This information must be correct
in order for the monitor to
correctly calculate output power.
5. Press “Power” to confirm your
selection. The status monitor will
display “End” to indicate that
programming is complete.
display “End” to indicate that
programming is complete.
During amplifier operation, press the
“Mode” button repeatedly to scroll
through the available information.
The status monitor will display
output power in Watts, input current
in Amperes, input voltage, heatsink
temperature (measured near the
output devices) in F° or C°.
“Mode” button repeatedly to scroll
through the available information.
The status monitor will display
output power in Watts, input current
in Amperes, input voltage, heatsink
temperature (measured near the
output devices) in F° or C°.
Adjusting Amplifier Input Level,
Crossover and Bass Boost
Crossover and Bass Boost
Setting Input Level
Initially, turn the input level control
to its fully counterclockwise
position. Turn on the source unit,
and increase the volume control
until it is approximately 3/4 of
maximum output level. Slowly turn
the input level control (clockwise)
while listening to the quality of the
reproduced sound. When you hear
distortion on the music peaks, turn
the level control back slightly. This
is the maximum undistorted output
level of your system. Turning the
level control up past this level WILL
NOT INCREASE THE MAXIMUM
OUTPUT POWER OF YOUR
AMPLIFIER! It will only decrease
the amount of volume control
rotation before the amp is at full
output power. It will also increase
the amount of extraneous noise
present in your system.
Initially, turn the input level control
to its fully counterclockwise
position. Turn on the source unit,
and increase the volume control
until it is approximately 3/4 of
maximum output level. Slowly turn
the input level control (clockwise)
while listening to the quality of the
reproduced sound. When you hear
distortion on the music peaks, turn
the level control back slightly. This
is the maximum undistorted output
level of your system. Turning the
level control up past this level WILL
NOT INCREASE THE MAXIMUM
OUTPUT POWER OF YOUR
AMPLIFIER! It will only decrease
the amount of volume control
rotation before the amp is at full
output power. It will also increase
the amount of extraneous noise
present in your system.
Setting the Crossover
A1201GTi and A601GTi
The 24dB/octave low-pass filter built
into your A1201GTi or A601GTi can
be adjusted to any frequency between
32Hz and 320Hz. You should choose
a crossover frequency that prevents
vocals and other midrange information
from being reproduced by your
subwoofer. Turning the knob
counterclockwise will decrease the
crossover frequency and turning it
clockwise will increase it.
The 24dB/octave low-pass filter built
into your A1201GTi or A601GTi can
be adjusted to any frequency between
32Hz and 320Hz. You should choose
a crossover frequency that prevents
vocals and other midrange information
from being reproduced by your
subwoofer. Turning the knob
counterclockwise will decrease the
crossover frequency and turning it
clockwise will increase it.
A302GTi
The 24dB/octave crossover built into
your A302GTi can be selected as a
low-pass filter (LPF), a high-pass filter
(HPF) or it may be defeated (Flat).
If your A302GTi will be used to drive
subwoofers, select LPF and adjust
the crossover according to the
instructions above for the A1201GTi
and A601GTi. If your A302GTi will
be used to drive midrange and high-
frequency speakers, you should set
the crossover as HPF and select a
frequency that minimizes the
distortion present in the speaker’s
output while allowing the speaker
to produce as much low-frequency
information as it can with minimum
distortion. Adjust the crossover
frequency after setting the level
control as described above. If your
A302GTi will be used to drive
midrange and high-frequency
speakers as well as a subwoofer,
defeat the crossover (Flat).
The 24dB/octave crossover built into
your A302GTi can be selected as a
low-pass filter (LPF), a high-pass filter
(HPF) or it may be defeated (Flat).
If your A302GTi will be used to drive
subwoofers, select LPF and adjust
the crossover according to the
instructions above for the A1201GTi
and A601GTi. If your A302GTi will
be used to drive midrange and high-
frequency speakers, you should set
the crossover as HPF and select a
frequency that minimizes the
distortion present in the speaker’s
output while allowing the speaker
to produce as much low-frequency
information as it can with minimum
distortion. Adjust the crossover
frequency after setting the level
control as described above. If your
A302GTi will be used to drive
midrange and high-frequency
speakers as well as a subwoofer,
defeat the crossover (Flat).
Setting the Bass Boost
(A601GTi and A1201GTi)
Use this control to add as much
as 6dB of boost at 50Hz. You may
set this control according to your
preference.
(A601GTi and A1201GTi)
Use this control to add as much
as 6dB of boost at 50Hz. You may
set this control according to your
preference.
06
The Official Brand of Live Music
Click on the first or last page to see other A302GTi service manuals if exist.