Read JBL TLX PS10 User Guide / Operation Manual online
Troubleshooting
three.
Operation
Mode
Procedure
LED Status
Off
Receiver/amplifier off
Red
On
Receiver/amplifier on and playing program material
Green
Standby
Simply turn off your receiver/amplifier. The subwoofer will
Red
turn off after approximately five minutes. The subwoofer
will turn on when your receiver/amplifier begins playing again.
will turn on when your receiver/amplifier begins playing again.
Volume
Crossover Frequency
The crossover frequency knob
determines the highest fre-
quency your subwoofer will
reproduce. It allows a seam-
less transition from the
subwoofer to the satellite
speakers. Experiment with
determines the highest fre-
quency your subwoofer will
reproduce. It allows a seam-
less transition from the
subwoofer to the satellite
speakers. Experiment with
this adjustment to find the
crossover frequency that
sounds best with your
speakers. When using the
speaker level connections,
the crossover adjustment will
also limit the low frequencies
crossover frequency that
sounds best with your
speakers. When using the
speaker level connections,
the crossover adjustment will
also limit the low frequencies
being sent to your satellite
speakers. This means that
your satellites won’t have
to try and reproduce the
information the subwoofer
is playing.
speakers. This means that
your satellites won’t have
to try and reproduce the
information the subwoofer
is playing.
If you used the high-le vel
(speaker) inputs and there
is no sound from any of the
speakers, check the
following:
(speaker) inputs and there
is no sound from any of the
speakers, check the
following:
• Receiver/amplifier is on
and a source is playing.
• Powered subwoofer is
plugged in.
• Check all wires and connec-
tions between receiver/
amplifier and speakers. Make
sure all wires are connected.
Make sure none of the
speaker wires are frayed,
cut, or punctured.
• Review proper operation
of your receiver/amplifier.
and a source is playing.
• Powered subwoofer is
plugged in.
• Check all wires and connec-
tions between receiver/
amplifier and speakers. Make
sure all wires are connected.
Make sure none of the
speaker wires are frayed,
cut, or punctured.
• Review proper operation
of your receiver/amplifier.
If there is low bass output,
check the following:
check the following:
• Make sure the connections
to the left and right “Speaker
Inputs” have the correct
polarity (+ and –).
• Make sure that the sub-
woofer is plugged into an
active electrical outlet.
• Powered subwoofer is
plugged in.
• Adjust the crossover point.
to the left and right “Speaker
Inputs” have the correct
polarity (+ and –).
• Make sure that the sub-
woofer is plugged into an
active electrical outlet.
• Powered subwoofer is
plugged in.
• Adjust the crossover point.
If you used the line-level
inputs and there is no
sound from the subwoofer,
check the following:
inputs and there is no
sound from the subwoofer,
check the following:
• Receiver/amplifier is on
and a source is playing.
• Powered subwoofer is
plugged in.
• Check all wires and con-
nections between receiver/
amplifier and subwoofer.
Make sure all wires are con-
nected. Make sure none of
the wires are frayed, cut, or
punctured.
• Review proper operation of
your receiver/amplifier.
and a source is playing.
• Powered subwoofer is
plugged in.
• Check all wires and con-
nections between receiver/
amplifier and subwoofer.
Make sure all wires are con-
nected. Make sure none of
the wires are frayed, cut, or
punctured.
• Review proper operation of
your receiver/amplifier.
TLX PS10/PS12 OM 7/22/98 3:00 PM Page 4
Click on the first or last page to see other TLX PS10 service manuals if exist.