Read JBL SCS 200 (serv.man2) User Guide / Operation Manual online
7
Important Safety Note: The
customer is solely responsi-
ble for proper selection of
mounting hardware not
included with the speakers,
and for proper assembly and
installation of the wall-brack-
ets, including but not limited
to the selection of appropri-
ate weight-bearing supports
and proper use of the
bracket. JBL disclaims any
liability for the selection of
mounting hardware and/or
bracket installation. Be sure
to follow these bracket
assembly and installation
instructions carefully. If you
have any questions or
doubts about your ability to
correctly wall-mount the
speakers, consult with your
authorized JBL dealer or
custom installer.
customer is solely responsi-
ble for proper selection of
mounting hardware not
included with the speakers,
and for proper assembly and
installation of the wall-brack-
ets, including but not limited
to the selection of appropri-
ate weight-bearing supports
and proper use of the
bracket. JBL disclaims any
liability for the selection of
mounting hardware and/or
bracket installation. Be sure
to follow these bracket
assembly and installation
instructions carefully. If you
have any questions or
doubts about your ability to
correctly wall-mount the
speakers, consult with your
authorized JBL dealer or
custom installer.
Step 1: Unscrew and remove
the large Molded Nut
the large Molded Nut
™
. If
necessary, use the supplied
Metal Bar
Metal Bar
∞
as a lever by
inserting it into one of the
holes in the outer edge of the
Molded Nut
holes in the outer edge of the
Molded Nut
™
.
Step 2: Firmly grasp the Ball
and Shaft
and Shaft
£
and pull it
straight out of the Attach-
ment Plate
ment Plate
¢
. Avoid leaning
it to the side for leverage, as
this may break off a tab.
this may break off a tab.
Step 3: Slide the Molded Nut
™
onto the Ball and Shaft
£
with the threaded open-
ing facing the ball. Thread
the Metal Nut ¡ all the way
onto the Ball and Shaft £,
with the star washer side
away from the ball. Refer to
the exploded drawing for the
proper orientation of these
three parts.
the Metal Nut ¡ all the way
onto the Ball and Shaft £,
with the star washer side
away from the ball. Refer to
the exploded drawing for the
proper orientation of these
three parts.
Step 4: Screw the Ball and
Shaft
Shaft
£
into the Threaded
Insert
§
on the back of the
Satellite Speaker
¶
until
it is fully seated in the
Threaded Insert
Threaded Insert
§
, but do
not tighten as you might dis-
lodge the Threaded Insert
§. Such damage would
not be covered under the
warranty.
lodge the Threaded Insert
§. Such damage would
not be covered under the
warranty.
Step 5: Tighten the Metal Nut
¡
with the star washer side
between the Metal Nut
¡
and the back of the Satellite
Speaker
Speaker
¶
, using large
needle-nose pliers until it is
firmly seated against the
back of the Speaker
firmly seated against the
back of the Speaker
¶
and
has locked the Ball and
Shaft
Shaft
£
and the Speaker
¶
together.
Note that once the Metal
Nut
Note that once the Metal
Nut
¡
is fully tightened, it
may embed some marks on
the back of the Satellite
Speaker
the back of the Satellite
Speaker
¶
. However, these
marks will be covered by the
Metal Nut
Metal Nut
¡
.
Step 6: Mount the Attach-
ment Plate
ment Plate
¢
into a wood
stud on the wall, using four
#10 pan-head wood screws
at least one inch long (not
supplied)
#10 pan-head wood screws
at least one inch long (not
supplied)
•
.
Make sure that all four
screws are driven into the
stud and not into drywall.
screws are driven into the
stud and not into drywall.
If the bracket needs to be
mounted in drywall, the
customer is responsible for
selecting and using appro-
priate wall-anchors and
screws.
mounted in drywall, the
customer is responsible for
selecting and using appro-
priate wall-anchors and
screws.
Important Note: The Metal
Nut
Nut
¡
must be fully tight-
ened against the Satellite
WALL-MOUNTING
2
3
4
8
5
1
1
2
3
4
5
6
7
8
Click on the first or last page to see other SCS 200 (serv.man2) service manuals if exist.