Read JBL SCS 200 (serv.man10) Service Manual online
7
Important Safety Note: The
customer is solely responsi-
ble for proper selection of
mounting hardware not
included with the speakers,
and for proper assembly and
installation of the wall-brack-
ets, including but not limited
to the selection of appropri-
ate weight-bearing supports
and proper use of the
bracket. JBL disclaims any
liability for the selection of
mounting hardware and/or
bracket installation. Be sure
to follow these bracket
assembly and installation
instructions carefully. If you
have any questions or
doubts about your ability to
correctly wall-mount the
speakers, consult with your
authorized JBL dealer or
custom installer.
customer is solely responsi-
ble for proper selection of
mounting hardware not
included with the speakers,
and for proper assembly and
installation of the wall-brack-
ets, including but not limited
to the selection of appropri-
ate weight-bearing supports
and proper use of the
bracket. JBL disclaims any
liability for the selection of
mounting hardware and/or
bracket installation. Be sure
to follow these bracket
assembly and installation
instructions carefully. If you
have any questions or
doubts about your ability to
correctly wall-mount the
speakers, consult with your
authorized JBL dealer or
custom installer.
Step 1: Unscrew and remove
the large Molded Nut
the large Molded Nut
™
. If
necessary, use the supplied
Metal Bar
Metal Bar
∞
as a lever by
inserting it into one of the
holes in the outer edge of the
Molded Nut
holes in the outer edge of the
Molded Nut
™
.
Step 2: Firmly grasp the Ball
and Shaft
and Shaft
£
and pull it
straight out of the Attach-
ment Plate
ment Plate
¢
. Avoid leaning
it to the side for leverage, as
this may break off a tab.
this may break off a tab.
Step 3: Slide the Molded Nut
™
onto the Ball and Shaft
£
with the threaded open-
ing facing the ball. Thread
the Metal Nut
the Metal Nut
¡
all the way
onto the Ball and Shaft
£
,
with the Metal Nut’s
¡
“knurled” surface facing
away from the ball. Refer to
the exploded drawing for the
proper orientation of these
three parts.
away from the ball. Refer to
the exploded drawing for the
proper orientation of these
three parts.
Step 4: Screw the Ball and
Shaft
Shaft
£
into the Threaded
Insert
§
on the back of the
Satellite Speaker
¶
until it
is fully seated in the
Threaded Insert
Threaded Insert
§
.
Step 5: Tighten the Metal Nut
¡
using a crescent wrench
(spanner) until it is firmly
seated against the back of
the Satellite Speaker
seated against the back of
the Satellite Speaker
¶
and
has locked the Ball and
Shaft
£
and the Satellite
Speaker
¶
together. Note
that once the Metal Nut
¡
is
fully tightened, it may embed
some marks on the back of
the Satellite Speaker
some marks on the back of
the Satellite Speaker
¶
.
However, these marks will be
covered by the Metal Nut
covered by the Metal Nut
¡
.
Step 6: Mount the Attach-
ment Plate
ment Plate
¢
into a wood
stud on the wall, using four
#10 pan-head wood screws
at least one inch long (not
supplied)
#10 pan-head wood screws
at least one inch long (not
supplied)
•
. Make sure that
all four screws are driven
into the stud and not into dry-
wall.
into the stud and not into dry-
wall.
If the bracket needs to be
mounted in drywall, the
customer is responsible for
selecting and using appro-
priate wall-anchors and
screws.
mounted in drywall, the
customer is responsible for
selecting and using appro-
priate wall-anchors and
screws.
Step 7: Holding the Satellite
Speaker
Speaker
¶
with both hands,
reinsert the ball portion of
the Ball and Shaft
the Ball and Shaft
£
into the
Attachment Plate
¢
.
Step 8: Hand-tighten the
Molded Nut
Molded Nut
™
while posi-
tioning the speaker for the
desired orientation. The
swiveling ball enables you to
aim the speaker to one side
or the other, or to tilt it up
desired orientation. The
swiveling ball enables you to
aim the speaker to one side
or the other, or to tilt it up
WALL-MOUNTING
1
2
3
4
8
5
1
2
3
4
5
6
7
8
JBL
SCS200.5/230 Service Manual
Page 8 of 53
Click on the first or last page to see other SCS 200 (serv.man10) service manuals if exist.