Read JBL SCS 120 Sub (serv.man2) User Guide / Operation Manual online
SCS120 System
Frequency Response
40Hz – 20kHz (
40Hz – 20kHz (
±
3dB)
sat20
Recommended Power
10 – 120 watts
Frequency Response
120Hz – 20kHz (
10 – 120 watts
Frequency Response
120Hz – 20kHz (
±
3dB)
Impedance
8 ohms nominal
Sensitivity
90dB @ 1 watt/1 meter
Crossover Frequency
3.5kHz (midrange to tweeter)
Tweeter
One 3/4" titanium composite
dome, video-shielded
Midrange
Two 3-1/2" neodymium
drivers, video-shielded
Dimensions (HxWxD)
14 x 4-3/8 x 6 inches
356 x 111 x 152mm
Weight
3.5 lbs/1.6 kg
8 ohms nominal
Sensitivity
90dB @ 1 watt/1 meter
Crossover Frequency
3.5kHz (midrange to tweeter)
Tweeter
One 3/4" titanium composite
dome, video-shielded
Midrange
Two 3-1/2" neodymium
drivers, video-shielded
Dimensions (HxWxD)
14 x 4-3/8 x 6 inches
356 x 111 x 152mm
Weight
3.5 lbs/1.6 kg
bass20
Amplifier
150 watts RMS
Frequency Response
40Hz – 120Hz (
150 watts RMS
Frequency Response
40Hz – 120Hz (
±
3dB)
Crossover Frequency
120Hz (subwoofer to satellite)
Bass
Dual 8" woofers, bass reflex
enclosure
Dimensions (HxWxD)
17-3/4 x 10 x 24 inches
451 x 254 x 610mm
Weight
42 lbs/19.1 kg
120Hz (subwoofer to satellite)
Bass
Dual 8" woofers, bass reflex
enclosure
Dimensions (HxWxD)
17-3/4 x 10 x 24 inches
451 x 254 x 610mm
Weight
42 lbs/19.1 kg
Specifications
Refinements may be made on
occasion to existing products
without notice, but will always
meet or exceed original speci-
fications unless otherwise
stated.
occasion to existing products
without notice, but will always
meet or exceed original speci-
fications unless otherwise
stated.
If there is no sound from
any of the speakers, check
the following:
any of the speakers, check
the following:
• Receiver/amplifier is on and
a source is playing.
• Powered subwoofer is
plugged in and is either in
the “On” or “Auto” position.
• Check all wires and con-
nections between receiver/
amplifier and speakers. Make
sure all wires are connected.
Make sure none of the speaker
wires are frayed, cut, or
punctured.
• Review proper operation of
your receiver/amplifier.
a source is playing.
• Powered subwoofer is
plugged in and is either in
the “On” or “Auto” position.
• Check all wires and con-
nections between receiver/
amplifier and speakers. Make
sure all wires are connected.
Make sure none of the speaker
wires are frayed, cut, or
punctured.
• Review proper operation of
your receiver/amplifier.
If there is no sound coming
from one speaker, check the
following:
from one speaker, check the
following:
• Check the “Balance” control
on your receiver/amplifier.
• Check all wires and con-
nections between receiver/
amplifier and speakers. Make
sure all wires are connected.
on your receiver/amplifier.
• Check all wires and con-
nections between receiver/
amplifier and speakers. Make
sure all wires are connected.
Make sure none of the
speaker wires are frayed, cut,
or punctured.
speaker wires are frayed, cut,
or punctured.
If the system plays at low
volumes but shuts off as
volume is increased, check
the following:
volumes but shuts off as
volume is increased, check
the following:
• Check all wires and con-
nections between receiver/
amplifier and speakers. Make
sure all wires are connected.
Make sure none of the
speaker wires are frayed, cut,
or punctured.
• If more than one pair of
main speakers is being used,
check the minimum imped-
ance requirements of your
receiver/amplifier.
nections between receiver/
amplifier and speakers. Make
sure all wires are connected.
Make sure none of the
speaker wires are frayed, cut,
or punctured.
• If more than one pair of
main speakers is being used,
check the minimum imped-
ance requirements of your
receiver/amplifier.
If there is low bass output,
check the following:
check the following:
• Make sure the connections
to the left and right “Speaker
Inputs” have the correct
polarity (+ and –).
to the left and right “Speaker
Inputs” have the correct
polarity (+ and –).
• Make sure that the sub-
woofer is plugged into an
active electrical outlet.
• Powered subwoofer is
plugged in and is either in
the “On” or “Auto” position.
woofer is plugged into an
active electrical outlet.
• Powered subwoofer is
plugged in and is either in
the “On” or “Auto” position.
If there is no sound from
the surround speakers,
check the following:
the surround speakers,
check the following:
• Check all wires and con-
nections between receiver/
amplifier and speakers. Make
sure all wires are connected.
Make sure none of the
speaker wires are frayed, cut,
or punctured.
• Review proper operation of
your receiver/amplifier and its
surround sound features.
• Make sure the movie or TV
show, you are watching is
recorded in Dolby surround. If
it is not, check to see if your
receiver/amplifier has other
surround modes you may use.
nections between receiver/
amplifier and speakers. Make
sure all wires are connected.
Make sure none of the
speaker wires are frayed, cut,
or punctured.
• Review proper operation of
your receiver/amplifier and its
surround sound features.
• Make sure the movie or TV
show, you are watching is
recorded in Dolby surround. If
it is not, check to see if your
receiver/amplifier has other
surround modes you may use.
Troubleshooting
SCS120 Simply Cinema OM 7/20/98 12:39 PM Page 7
Click on the first or last page to see other SCS 120 Sub (serv.man2) service manuals if exist.