Read JBL SB 400 Service Manual online
2.3 P
INOUT
C
ATEGORY
D
ETAILS
Power:
3.3v supply pins are provided on either side of the module. These pins are all internally connected inside of the SiP
and are provided for convenience so that Ginseng can be powered from either the left or right sides to make
routing a PCB convenient for various applications. It is generally recommended to power the 3.3V bus from only
one side of the SiP. The pins on the other side should be shunted to ground through a 0.1uF and 1uF set of
capacitors.
and are provided for convenience so that Ginseng can be powered from either the left or right sides to make
routing a PCB convenient for various applications. It is generally recommended to power the 3.3V bus from only
one side of the SiP. The pins on the other side should be shunted to ground through a 0.1uF and 1uF set of
capacitors.
XPD:
The XPD port is a SPI bus used for loading module firmware during development and mass production and also for
debugging. One of the following two styles of XPD port connectors should be included on all motherboard designs
that use Ginseng to ensure that loading code and debugging can be done easily. The XPD port interfaces to the
XPD module which provides an interface to a host computer via RS-232 or USB. The XPD port operates from the
V
debugging. One of the following two styles of XPD port connectors should be included on all motherboard designs
that use Ginseng to ensure that loading code and debugging can be done easily. The XPD port interfaces to the
XPD module which provides an interface to a host computer via RS-232 or USB. The XPD port operates from the
V
CC
bus. To ensure proper functionality of the XPD interface, be sure to minimize the amount of capacitance on
the XPD lines. Note: the XPD_RESET / EXT_RST pin is tolerant up to 1.8V MAX -- if control of the Reset pin is
desired, a series diode must be used to guarantee the input voltage does not exceed the 1.8V max.
desired, a series diode must be used to guarantee the input voltage does not exceed the 1.8V max.
Figure 1 - XPD Pinout
Digital IO:
Ginseng has general purpose digital IO (“GPIO”) pins available for use by the application firmware. GPIO pins use
the same logic voltage as the 3.3V pin and have the following software configurable features: IO direction, drive
strength (for output only), Schmitt Trigger (for input only), pull up (input only), pull down (input only), slew rate
(output only). Ginseng is also capable of active-high and active-low configuration of LEDs.
the same logic voltage as the 3.3V pin and have the following software configurable features: IO direction, drive
strength (for output only), Schmitt Trigger (for input only), pull up (input only), pull down (input only), slew rate
(output only). Ginseng is also capable of active-high and active-low configuration of LEDs.
VCC
1x8 Classic
1
XPD
3.3V
VCC
SCK
PB0
MISO
MOSI
MOSI
GND
PB1
Reset
2
3
4
5
6
7
8
3
4
5
6
7
8
XPD_SCK
XPD_PB0
XPD_MOSI
XPD_MISO
XPD_PB0
XPD_MOSI
XPD_MISO
XPD_PB1
EXT_RST
EXT_RST
VCC
PB0
MOSI
PB1
SCK
MISO
GND
Reset
2x4
1
3
5
7
2
4
6
8
FTS-104-01-L-DV
XPD PB0
XPD MOSI
XPD PB1
XPD SCK
XPD MISO
EXT RST
3.3V
G
INSENG
M
ODULE
D
ATASHEET
-
D
IGITAL
W
IRELESS
A
UDIO
S
OLUTION FOR
G
ENERAL
A
PPLICATIONS
DO1620 - Ginseng Data sheet (rev. 1.2) 2012-04-02 Page 11 of 40
JBL
SB 400 Service Manual
Page 20 of 30
Click on the first or last page to see other SB 400 service manuals if exist.