Read JBL ON STAGEII (serv.man12) EMC - CB Certificate online
IEC 60950-1 1st. Ed, 2001
- Page 6 of 6 -
Order No. 46974
6.2.2.1
Add the symbol NZ in the right hand margin
beside the first paragraph including Note 1.
Delete Note 2
Add the following after the first paragraph:
In Australia (this variation does not apply in
New Zealand), the electrical separation is
subjected to 10 impulses of alternating
polarity, using the impulse test generator of
annex N for 10/700µs impulses. The interval
between successive impulses is 60 s
and the initial voltage, Uc, is:
for 6.2.1 a):7.0 kV for hand-held telephones
and for headsets and 2.5 kV for other
equipment; and
for 6.2.1 b) and 6.2.1 c):1.5 kV.
NOTE 201 – The 7 kV impulse simulates
lightning surges on typical rural and semi-rural
network lines.
NOTE 202 – The value of 2.5 kV for 6.2.1 a)
was chosen to ensure the adequacy of the
insulation concerned and does not necessarily
simulate likely overvoltages.
beside the first paragraph including Note 1.
Delete Note 2
Add the following after the first paragraph:
In Australia (this variation does not apply in
New Zealand), the electrical separation is
subjected to 10 impulses of alternating
polarity, using the impulse test generator of
annex N for 10/700µs impulses. The interval
between successive impulses is 60 s
and the initial voltage, Uc, is:
for 6.2.1 a):7.0 kV for hand-held telephones
and for headsets and 2.5 kV for other
equipment; and
for 6.2.1 b) and 6.2.1 c):1.5 kV.
NOTE 201 – The 7 kV impulse simulates
lightning surges on typical rural and semi-rural
network lines.
NOTE 202 – The value of 2.5 kV for 6.2.1 a)
was chosen to ensure the adequacy of the
insulation concerned and does not necessarily
simulate likely overvoltages.
No TNV circuitry.
N/A
6.2.2.2
Add the symbol NZ in the right hand margin
beside the second paragraph.
Delete the Note.
Add the following after the second paragraph:
In Australia (this variation does not apply in
New Zealand), the a.c. test voltage is:
for 6.2.1 a):3 kV; and
for 6.2.1 b) and 6.2.1 c):1.5 kV.
NOTE 201 – Where there are capacitors
across the insulation under test, it is
recommended that d.c. test voltages are used.
NOTE 202 – The 3 kV and 1.5 kV values have
been determined considering the low
frequency induced voltages from the power
supply distribution system.
beside the second paragraph.
Delete the Note.
Add the following after the second paragraph:
In Australia (this variation does not apply in
New Zealand), the a.c. test voltage is:
for 6.2.1 a):3 kV; and
for 6.2.1 b) and 6.2.1 c):1.5 kV.
NOTE 201 – Where there are capacitors
across the insulation under test, it is
recommended that d.c. test voltages are used.
NOTE 202 – The 3 kV and 1.5 kV values have
been determined considering the low
frequency induced voltages from the power
supply distribution system.
No TNV circuitry.
N/A
Annex P
Add the following Normative References to Annex P:
IEC 60065, Audio, Video and similar electronic
apparatus—Safety requirements
AS/NZS 3191, Approval and test specification—
Electric flexible cords
AS/NZS 3112, Approval and test specification—
Plugs and socket-outlets
AS/NZS 4695.707, Fire hazard testing of
electrotechnical products—Methods of test for the
determination of the flammability
of solid electrical insulating materials when exposed
to an igniting source
IEC 60065, Audio, Video and similar electronic
apparatus—Safety requirements
AS/NZS 3191, Approval and test specification—
Electric flexible cords
AS/NZS 3112, Approval and test specification—
Plugs and socket-outlets
AS/NZS 4695.707, Fire hazard testing of
electrotechnical products—Methods of test for the
determination of the flammability
of solid electrical insulating materials when exposed
to an igniting source
Considered.
—
Index
Between the entries for ‘polyimide insulating
material’ and ‘powder’ insert the following:
potential ignition source 1.12.201, 4.7.201.3,
4.7.201.5
material’ and ‘powder’ insert the following:
potential ignition source 1.12.201, 4.7.201.3,
4.7.201.5
Considered. N/A
Click on the first or last page to see other ON STAGEII (serv.man12) service manuals if exist.