Read JBL ON BEAT RUMBLE (serv.man6) Service Manual online
JBL
Service Manual
OnBeat Rumble
Lightning Docking station for iPhone 5, iPad, iPad Mini.
Released EU2013
Harman International
Rev 0, 06/2013
8500 Balboa Boulevard
ESD WARNING
2
OWNER’S MANUAL
3
EXPLODED VIEW AND PARTS
9
SCHEMATIC DIAGRAMS
10
CONTENTS
Each precaution in this manual should be followed during servicing.
Components identified with the IEC symbol
in the parts list are special significance to safety. When replacing a component identified with
, use only the replacement parts designated, or parts with the same ratings or resistance, wattage, or voltage that are designated in the
parts list in this manual. Leakage-current or resistance measurements must be made to determine that exposed parts are acceptably
insulated from the supply circuit before retuming the product to the customer.
Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are called
Electrostatically Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field effect transistors and
semiconductor "chip" components.
The following techniques should be used to help reduce the incidence of component damage caused by static electricity.
1. Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off any electrostatic charge on
your body by touching a known earth ground. Alternatively, obtain and wear a commercially available discharging wrist strap device,
which should be removed for potential shock reasons prior to applying power to the unit under test.
2. After removing an electrical assembly equipped with ES devices, place the assembly on a conductive surface such as aluminum foil, to
prevent electrostatic charge build-up or exposure of the assembly.
3. Use only a grounded-tip soldering iron to solder or unsolder ES devices.
4. Use only an anti-static solder removal device. Some solder removal devices not classified as "anti-static" can generate electrical charges
sufficient to damage ES devices.
5. Do not use freon-propelled chemicals. These can generate electrical change sufficient to damage ES devices.
6. Do not remove a replacement ES device from its protective package until immediately before you are ready to install it. (Most replacement
ES devices are packaged with leads electrically shorted together by conductive foam, aluminum foil or comparable conductive material.)
7. Immediately before removing the protective material from the leads of a replacement ES device, touch the protective material to the
chassis or circuit assembly into which the device will be installed.
Be sure no power is applied to the chassis or circuit, and observe all other safety precautions.
8. Minimize bodily motions when handling unpackaged replacement ES devices. (Otherwise harmless motion such as the brushing together
or your clothes fabric or the lifting of your foot from a carpeted floor can generate static electricity sufficient to damage an ES devices.
CAUTION :
JBL
OnBeat Xtreme Service Manual
Page 2 of 47
Quick Setup Guide
JBL
®
OnBeat
RumBLe
™
WeLcOme
Thank you for purchasing the JBL
®
OnBeat Rumble
™
speaker dock. This quick setup guide
will show you how to connect and set up your dock.
IncLuDeD ItemS
AC Cord (varies by region)
Power Supply
JBL OnBeat Rumble Speaker Dock
2
cOnnectIOnS
Power
Connector
Headphone
Connector
Auxiliary
Input
USB
Connector
1. If you are going to use your JBL OnBeat Rumble speaker dock with another audio
source, plug one end of a 3.5mm (1/8") stereo cable (not supplied) into the dock’s
Auxiliary Input connector, and plug the other end into the audio source’s audio-out or
headphone-out connector.
2. If you want to use headphones (such as when previewing mixes with a DJ app), plug
them into the dock’s Headphone connector.
3. Plug the dock’s power supply into the Power connector on the rear of the dock and
then into a working AC power outlet. The dock will automatically turn on and go into the
Bluetooth
®
pairing mode (the Source button LED will be flashing blue).
4. The USB port can be used for charging your iPod, iPhone or iPad device.
PLACEMENT
Place the JBL OnBeat Rumble speaker dock on a shelf or table with the rear of its enclosure
at least 3" (76mm) away from a wall or other surface to allow the bass ports to operate
properly.
CONTROLS AND INDICATORS
Bass Boost Button
and LED
Volume Down
Button
Volume Up
Button
Club EQ Button
and LED
Dock
Lid
Power Button
and LED
Source Button
and LED