Read JBL MEDIA 3 Service Manual online
2
Two-way Powered Speaker System
Media 3
Please refer to the explosion drawing, the disassembly
procedures are as follows:
procedures are as follows:
For Master Speaker
Step 1
Unscrew 6 M3.5x15 screws (36) from rear panel (35).
Separate the Front and Rear Panels (8) (35).
Separate the Front and Rear Panels (8) (35).
Step 2
To disassemble the Heat-sink (31) from IC PCB (25)
unscrew 4 M3x8 (33) screws from Rear Panel.
unscrew 4 M3x8 (33) screws from Rear Panel.
Disassemblingthe Heat-sink
Unscrew 2 M3x12 (26) screws from the IC PCB (25).
Unscrew 4 M3x5 ISO screws (33) of IC PCB (25).
Unscrew 4 M3x5 ISO screws (32) from Heat-sink (31).
Hexagon bronze stick between Heat-sink and IC PCB (25)
will be loosened at the same time.
Hexagon bronze stick between Heat-sink and IC PCB (25)
will be loosened at the same time.
Step 3 (RCA PCB(28)
Unscrew 2 M3x8 screw (30) on Rear Panel, then take out
the RCA bracket. The RCA PCB (28) can be separated
from the shell also.
the RCA bracket. The RCA PCB (28) can be separated
from the shell also.
Step 4 (Front Panel)
To disassemble VR PCB (22) remove 3 VR knobs (6).
Unscrew 2 M3x6 screws (21).
Unscrew 2 M3x6 screws (21).
Remove VR PCB (22).
Loosen 3 internal caps (20).
To disassemble the LED PCB (17) unscrew M3x8 (18).
To disassemble the SW PCB (16) unscrew 2 M3x8 (14)
screws on Rear Panel.
screws on Rear Panel.
To disassemble the Earphone PCB (9) unscrew 2 M3x8
(11) screws on the Front Panel. Remove the bracket (10)
and Earphone PCB (9).
(11) screws on the Front Panel. Remove the bracket (10)
and Earphone PCB (9).
To disassemble the 1 ¾” Speaker (23) unscrew 2 M3.5x13
screws (24) from the internal side of the Front Panel.
screws (24) from the internal side of the Front Panel.
To disassemble the 4” Speaker remove the metal grille (3)
and unscrew 4 M3.5x13(4) screws. The Speaker can then
be removed.
and unscrew 4 M3.5x13(4) screws. The Speaker can then
be removed.
The Slave Speaker
Step 1
Unscrew 6 M3.5x15 screws (36) and separate the Front
and Rear Panels (38) & (39).
and Rear Panels (38) & (39).
Step 2 (Rear Panel)
To Disassemble RCA PCB (28) unscrew 2 M3x8 screws
(30) from Rear Panel. Take out RCA bracket (29), then
RCA PCB (28) can be removed from sink.
(30) from Rear Panel. Take out RCA bracket (29), then
RCA PCB (28) can be removed from sink.
Step 3 (Front Panel)
To disassemble 1 ¾” speak (23) Unscrew 2 M3.5x13
screws (24).
screws (24).
To disassemble 4” speaker (5) remove the grille (15)
and remove 4 M3.5x13 screws (4). Then the speaker
can be removed.
and remove 4 M3.5x13 screws (4). Then the speaker
can be removed.
DISASSEMBLY PROCEDURES
Click on the first or last page to see other MEDIA 3 service manuals if exist.