Read JBL ESC 300 Sub (serv.man14) User Guide / Operation Manual online
If there is no sound from any
of the speakers, check the
following:
of the speakers, check the
following:
• Make sure the subwoofer is
plugged into an active AC wall
outlet.
• Make sure the Master Power
Switch, located on the rear of
the subwoofer, is in the
“
plugged into an active AC wall
outlet.
• Make sure the Master Power
Switch, located on the rear of
the subwoofer, is in the
“
On/Standby” position.
• Make sure there is a
source – for example, a VCR or
television hooked up to the
video or auxiliary input jacks.
• Make sure that the program
material is playing.
• Recheck the hookup
connections in the “Speaker
Connections” section.
source – for example, a VCR or
television hooked up to the
video or auxiliary input jacks.
• Make sure that the program
material is playing.
• Recheck the hookup
connections in the “Speaker
Connections” section.
If there is no sound from the
surround speakers or
it is very low, check the
following:
surround speakers or
it is very low, check the
following:
• Check all connections
between processor/amplifier
and each of the speakers.
• Raise the surround volume
from the remote control (see
“
between processor/amplifier
and each of the speakers.
• Raise the surround volume
from the remote control (see
“
Operation” section).
• Make sure the TV show or
movie you are watching is
recorded in Dolby Surround.
If it is not, try the Phantom or
Simulated surround mode.
movie you are watching is
recorded in Dolby Surround.
If it is not, try the Phantom or
Simulated surround mode.
If there is no sound from the
center speaker, check the
following:
center speaker, check the
following:
• Make sure that the processor
is in the Pro Logic,
3 Stereo, or Simulated mode. If
it is in Phantom or Stereo
mode, the center speaker
will not play.
• Check the connections
between the subwoofer and the
center speaker.
is in the Pro Logic,
3 Stereo, or Simulated mode. If
it is in Phantom or Stereo
mode, the center speaker
will not play.
• Check the connections
between the subwoofer and the
center speaker.
If you have low bass output,
check the following:
check the following:
• Experiment with placement
of the subwoofer. Remember,
place the subwoofer in a
corner to get maximum bass
output from the system.
• Increase the level of bass,
using the remote control.
of the subwoofer. Remember,
place the subwoofer in a
corner to get maximum bass
output from the system.
• Increase the level of bass,
using the remote control.
Troubleshooting
Specifications
ESC300 System
Amplifier
200 watts total
system output;
front channels:
35 watts x 3 @ .1% THD;
surround channels:
15 watts x 2 @ .1% THD;
subwoofer:
65 watts x 1 @ 1% THD
Signal-to-Noise Ratio
90dB
Input Impedance
20k ohms
Input Sensitivity
400mV
Auto Turn-on Sensitivity
2mV/channel
System Frequency
Response (–6dB)
35Hz – 20kHz
200 watts total
system output;
front channels:
35 watts x 3 @ .1% THD;
surround channels:
15 watts x 2 @ .1% THD;
subwoofer:
65 watts x 1 @ 1% THD
Signal-to-Noise Ratio
90dB
Input Impedance
20k ohms
Input Sensitivity
400mV
Auto Turn-on Sensitivity
2mV/channel
System Frequency
Response (–6dB)
35Hz – 20kHz
Subwoofer
Dimensions (HxWxD)
15-1/8 x 13 x 14-1/2 inches
15-1/8 x 13 x 14-1/2 inches
384 x 330 x 368mm
Weight
34.5 lbs/15.7 kg
Weight
34.5 lbs/15.7 kg
Satellites (each)
Dimensions (HxWxD)
4-3/8 x 3-3/16 x 3-3/4 inches
111 x 81 x 95mm
4-3/8 x 3-3/16 x 3-3/4 inches
111 x 81 x 95mm
Weight
.8 lbs/.4 kg
.8 lbs/.4 kg
Occasional refinements may be
made to existing products
without notice, but will always
meet or exceed original
specifications unless otherwise
stated.
made to existing products
without notice, but will always
meet or exceed original
specifications unless otherwise
stated.
Click on the first or last page to see other ESC 300 Sub (serv.man14) service manuals if exist.