E 10 (serv.man4) - JBL Audio User Guide / Operation Manual

e 10 (serv.man4) user guide / operation manual
Model
E 10 (serv.man4)
Pages
4 Few pages! See other manuals at the bottom of the first or last page.
Size
315.14 KB
Type
PDF
Document
User Guide / Operation Manual
Brand
Device
Audio
File
e-10-sm4.pdf
Date

Read JBL E 10 (serv.man4) User Guide / Operation Manual online

OWNER’S GUIDE
®
E10, E20, EC25
NORTHRIDGE
E SERIES
SPEAKER PLACEMENT
Proper placement of the speak-
ers is an important step in
obtaining the most realistic
soundstage possible. These
recommendations are for the
optimum placement of the loud-
speakers. Use these placement
recommendations as a guide.
Slight variations will not dimin-
ish your listening pleasure. 
CONNECTION TIPS
Speakers and electronics termi-
nals have corresponding posi-
tive (+) and negative (–) termi-
nals. It is important to connect
both speakers identically: posi-
tive (+) on the speaker to posi-
tive (+) on the amplifier and
negative (–) on the speaker to
negative (–) on the amplifier.
Wiring “out of phase” results 
in thin sound, weak bass and 
a poor stereo image. 
With the advent of multichannel
surround sound systems, con-
necting all of the speakers in
your system with the correct
polarity remains as important as
ever in order to preserve the
proper ambience and direction-
ality of the program material.
To use the binding-post speaker
terminals, unscrew the colored
collar until the pass-through
hole in the center post is visible
under the collar. Insert the bare
end of the wire through this
hole; then screw the collar
down until the connection is
tight. 
SPEAKER CONNECTIONS
–     +
–    +
–       +
Receiver Speaker Outputs
LEFT
LEFT
RIGHT
RIGHT
–       +
40
o
 – 60
o
MODELS: E10, E20
MODEL: EC25
As front speakers
(0–0,6m)
MODELS: E10, E20, EC25
Place pads here
The supplied self-adhesive
rubber feet may be attached to
the bottom corners of your
speakers to protect your 
furniture.
MODELS: E10, E20
(1,5–1,8m)
MODEL: EC25
Receiver
Speaker Outputs
–     +
CENTER
CENTER
–                +
As surround speakers
TROUBLESHOOTING
If there is no sound from any
of the speakers:
• Check that receiver/amplifier
is on and that a source is 
playing.
• Review proper operation of
your receiver/amplifier.
If there is no sound coming
from one speaker:
• Check the “Balance” control
on your receiver/amplifier.
• Check all wires and connec-
tions between receiver/ampli-
fier and speakers. Make sure no
wires are touching other wires
or terminals and creating a
short circuit.
• Make sure all wires are con-
nected. Make sure none of the
speaker wires are frayed, cut or
punctured.
• In Dolby* Digital or DTS
®
mode, make sure that the
receiver/processor is config-
ured so that the speaker in
question is enabled.
• Turn off all electronics and
switch the speaker in question
with one of the other speakers
that is working correctly. Turn
everything back on, and deter-
mine whether the problem has
followed the speakers, or has
remained in the same channel.
If the problem is in the same
channel, the source of the prob-
lem is most likely with your
receiver or amplifier, and you
should consult the owner’s
manual for that product for fur-
ther information. If the problem
has followed the speaker, con-
sult your dealer for further
assistance or, if that is not pos-
sible, visit www.jbl.com for 
further information.
If the sys lays at low vol-
umes but shuts off as vol-
ume is increased:
• Check all wires and connec-
tions between receiver/ampli-
fier and speakers.
• Make sure all wires are con-
nected. Make sure none of the
speaker wires are frayed, cut or
punctured.
• If more than one pair of main
speakers is being used, check
the minimum impedance
requirements of your receiver/
amplifier.
If there is no (or low) bass
output:
• Make sure the polarities 
(+ and –) of the left and right
“Speaker Inputs” are con-
nected properly.
• Consider adding a powered
subwoofer to your system for
use with digital “.1” surround
formats.
If there is no sound from 
the surround speakers:
• Check all wires and con-
nections between receiver/
amplifier and speakers. Make
sure all wires are connected.
Make sure none of the speaker
wires are frayed, cut or punc-
tured.
• Review proper operation of
your receiver/amplifier and its
surround sound features.
• Make sure the movie or TV
show you are watching is
recorded in a surround sound
mode. If it is not, check to see
whether your receiver/amplifier
has other surround modes you
may use.
• In Dolby Digital or DTS mode,
make sure your receiver/pro-
cessor is configured so that the
surround speakers are enabled.
• Review the operation of your
DVD player and the jacket of
your DVD to make sure that the
DVD features the desired Dolby
Digital or DTS mode, and that
you have properly selected that
mode using both the DVD
player’s menu and the DVD
disc’s menu.
NOTICE:
Important Safety Notes 
• Proper selection of mounting
hardware and installation of the
wall brackets are the responsi-
bility of the customer. 
• This product is not intended
for ceiling mounting.
Two Number 8 round head or
pan head screws should be
used per loudspeaker. The
screw head should be between
5/16 inch (8mm) and 1/4 inch
(6.3mm) in diameter, and the
screw should be at least 2
inches (50mm) in length.
When installing screws in any
wall, always use properly
selected wall anchors. Attach
two of the four self-adhesive
rubber pads that came with the
E10 loudspeaker to the back of
the enclosure in the two bottom
corners so that the cabinet is
spaced evenly from the wall.
Select a suitable mounting loca-
tion on a wall. (The ceiling is not
a suitable mounting location.) 
Drill two pilot holes, appropri-
ately sized for the specific self-
tapping screw or wall anchor
that you will be using. The holes
should be 8 inches (203mm)
apart. See Figure 1. The holes
should be 3/4" (19mm) below
where you want the top of the
enclosure to be positioned. Use
a carpenter’s level to ensure
that the holes are even and that
the speaker will mount on the
level.
Install the two screws into
either a wooden wall stud or
anchor, and tighten them until
the back of each screw head is
about 1/8 inch (3mm) from the
wall. See Figure 2. Install the
loudspeaker by slowly moving
the cabinet toward the screws
so that the screw heads clear
the larger circular portion of the
two keyholes. Once both screw
heads have entered the key-
holes, the loudspeaker should
gently be lowered onto the
screw shafts. Check that the
loudspeaker is firmly locked
onto the screws by gently
pulling the speaker down and
forward. 
Fig. 1                                    Fig. 2
WALL-MOUNTING 
(Model E10 Only)
203 mm
3 mm
SPECIFICATIONS 
E10
E20
EC25
Description
Description
Description
2-Way 4" wall-mount/bookshelf 
2-Way 5" bookshelf 
2-Way dual 5" center
Maximum Recommended 
Maximum Recommended 
Maximum Recommended 
Amplifier Power**
Amplifier Power**
Amplifier Power**
100W
125W
150W
Power Handling
Power Handling
Power Handling
(Continuous/Peak)
(Continuous/Peak)
(Continuous/Peak)
50W/200W
60W/240W
75W/300W
Nominal Impedance
Nominal Impedance
Nominal Impedance
8 Ohms
8 Ohms
8 Ohms
Sensitivity (2.83V/1m)
Sensitivity (2.83V/1m)
Sensitivity (2.83V/1m)
86dB
86dB
90dB
Frequency Response (–3dB)
Frequency Response (–3dB)
Frequency Response (–3dB)
75Hz – 20kHz
68Hz – 20kHz
80Hz – 20kHz
Crossover Frequency
Crossover Frequency
Crossover Frequency
2000Hz
3000Hz
4000Hz
High-Frequency Transducer
High-Frequency Transducer
High-Frequency Transducer
3/4" (19mm) Titanium-laminate 
3/4" (19mm) Titanium-laminate
3/4" (19mm) Titanium-laminate 
dome, shielded 
dome, shielded 
dome, shielded
Low-Frequency Transducer
Low-Frequency Transducer
Low-Frequency Transducer
4" (100mm) PolyPlas,™ shielded
5" (130mm) PolyPlas,™ shielded
Dual 5" (130mm) PolyPlas,™ shielded
Baffle
Baffle
Baffle
Low diffraction, IsoPower™
Low diffraction, IsoPower™
Low diffraction, IsoPower™
Port
Port
Port
FreeFlow™ flared
FreeFlow™ flared
FreeFlow™ flared
Network
Network
Network
Straight-Line Signal Path™ (SSP)
Straight-Line Signal Path™ (SSP)
Straight-Line Signal Path™ (SSP)
Terminals
Terminals
Terminals
Gold-plated, 5-way binding posts
Gold-plated, 5-way binding posts
Gold-plated, 5-way binding posts
Dimensions (H x W x D)
Dimensions (H x W x D)
Dimensions (H x W x D)
10" x 10-1/8" x 5-1/4"
10-7/8" x 6" x 8-1/8"
6-7/8" x 18" x 10"
254mm x 257mm x 133mm
275mm x 153mm x 206mm
175mm x 457mm x 254mm
Weight Per Speaker
Weight Per Speaker
Weight Per Speaker
8 lb/3.6kg
7 lb/3.2kg
15.6 lb/7.1kg
Declaration of Conformity
We, Harman Consumer International
2, route de Tours 
72500 Chateau-du-Loir
France
declare in own responsibility, that the products described in
this owner’s manual are in compliance with technical stan-
dards: 
EN 50081-1:1992
EN 50082-1:1997
Gary Mardell
Harman Consumer International
Chateau-du-Loir, France 2/03
© 2003 Harman International Industries, Incorporated 
JBL is a registered trademark of Harman International Industries, Incorporated.
Part No.406-000-01530
PRO SOUND COMES HOME
JBL Consumer Products, 250 Crossways Park Drive, Woodbury, NY 11797 
2, route de Tours, 72500 Chateau-du-Loir, France
800.336.4JBL (4525) (USA only)  www.jbl.com
* Trademark of Dolby Laboratories.
DTS is a registered trademark of Digital Theater Systems, Inc.
** The maximum recommended amplifier power rating will ensure 
proper system headroom to allow for occasional peaks. We do not 
recommend sustained operation at these maximum power levels.
All features and specifications are subject to change without notice.
All dimensions include grilles.
Page of 4
Display

Download JBL E 10 (serv.man4) User Guide / Operation Manual

Here you can read online and download JBL E 10 (serv.man4) User Guide / Operation Manual in PDF. E 10 (serv.man4) user guide / operation manual will guide through the process and help you recover, restore, fix, disassemble and repair JBL E 10 (serv.man4) Audio. Information contained in service manuals typically includes schematics / circuit diagrams, wiring diagrams, block diagrams, printed wiring boards, exploded views, parts list, disassembly / assembly, pcb.