Read JBL CSS10 (serv.man2) User Guide / Operation Manual online
5
DOLBY PRO LOGIC
®
(NON-DIGITAL) – LINE LEVEL
Use this installation method
for Dolby Pro Logic
applications (not Dolby Digital,
DTS or other digital
processing), where the
receiver/processor is
equipped with a subwoofer
output, or a volumecontrolled
preamp (line-) level output:
for Dolby Pro Logic
applications (not Dolby Digital,
DTS or other digital
processing), where the
receiver/processor is
equipped with a subwoofer
output, or a volumecontrolled
preamp (line-) level output:
Use RCA-type interconnects
to connect the line-level
subwoofer outputs on your
receiver or amplifier to the
line-level inputs on the
subwoofer. IMPORTANT: Do
not use the LFE input on the
subwoofer with Dolby
Pro Logic processors.
to connect the line-level
subwoofer outputs on your
receiver or amplifier to the
line-level inputs on the
subwoofer. IMPORTANT: Do
not use the LFE input on the
subwoofer with Dolby
Pro Logic processors.
NOTE: If your receiver or
amplifier has only one
subwoofer output jack, then
you will need to use a Y-
connector (not included). Plug
the male end of the Y-connec-
tor into your receiver or ampli-
fier’s subwoofer output jack,
and connect each of the two
female ends to separate RCA-
type interconnects. Finally,
plug the RCA-type
interconnects into the line-
level inputs on the subwoofer.
amplifier has only one
subwoofer output jack, then
you will need to use a Y-
connector (not included). Plug
the male end of the Y-connec-
tor into your receiver or ampli-
fier’s subwoofer output jack,
and connect each of the two
female ends to separate RCA-
type interconnects. Finally,
plug the RCA-type
interconnects into the line-
level inputs on the subwoofer.
Connect each speaker to
the corresponding speaker
terminals on your receiver
or amplifier.
the corresponding speaker
terminals on your receiver
or amplifier.
Make sure your receiver or
processor is correctly config-
ured to indicate that the
subwoofer is “On.”
processor is correctly config-
ured to indicate that the
subwoofer is “On.”
Use this installation method
for Dolby Digital, DTS or other
digital surround processors:
for Dolby Digital, DTS or other
digital surround processors:
Use the line-level input jack
marked “LFE” for the Low-
Frequency Effects channel.
marked “LFE” for the Low-
Frequency Effects channel.
Connect this jack to the LFE
output or subwoofer output
on your receiver or amplifier.
Connect each speaker to
the corresponding speaker
terminals on your receiver
or amplifier.
output or subwoofer output
on your receiver or amplifier.
Connect each speaker to
the corresponding speaker
terminals on your receiver
or amplifier.
Make sure that you have con-
figured your surround sound
processor for “Sub-woofer
On.” Also configure your
receiver for 5.1-, 6.1-
figured your surround sound
processor for “Sub-woofer
On.” Also configure your
receiver for 5.1-, 6.1-
or 7.1-channel operation as
appropriate. The front left,
front right, center and rear
speakers should all be set
to “Small.” If your receiver
allows you to set the cross-
over frequency between the
subwoofer and the main
speakers, select 100Hz or
the setting that is the closest
frequency below it.
appropriate. The front left,
front right, center and rear
speakers should all be set
to “Small.” If your receiver
allows you to set the cross-
over frequency between the
subwoofer and the main
speakers, select 100Hz or
the setting that is the closest
frequency below it.
DOLBY
®
DIGITAL OR DTS
®
(OR OTHER DIGITAL SURROUND MODE) CONNECTION
LINE
LEVEL
IN
LFE
L
R
LFE OUT
RECEIVER
SUBWOOFER
– +
– +
– +
– +
– +
– +
– +
– +
– +
Left
Surround
Left
Front
Right
Front
Center
Right Front
Right Surround
Subwoofer
Receiver
Subwoofer
Out
Line
Level In
L
L
Left Front
Surround Back
Left
Surround Back
Right
Surround Back
Left
Right
Surround
Center
Surround Back
Right
– +
Left Surround
– +
– +
– +
– +
R
R
English
Click on the first or last page to see other CSS10 (serv.man2) service manuals if exist.