BASS 2 - JBL Audio Service Manual (repair manual)

bass 2 service manual
Model
BASS 2
Pages
14
Size
683.54 KB
Type
PDF
Document
Service Manual
Brand
Device
Audio
File
bass-2.pdf
Date

Read JBL BASS 2 Service Manual online

JBL Consumer Products Inc.
80 Crossways Park West
Woodbury, N.Y. 11797
1-800-336-4JBL in the USA
A Harman International Company
Part No.: 1112-BASS2/BASSWAVE
Bass2/Basswave
TECHNICAL MANUAL
Powered Subwoofer
1
Powered Subwoofer
BASS2/BASSWAVE
TABLE OF CONTENTS
Specifications .................................................................1
Features..........................................................................1
Disassembly Procedures................................................2
Packaging Exploded View .............................................2
Bass2/Basswave Exploded View...................................3
Test Procedure...............................................................4
Wiring Diagram...............................................................5
Parts Lists.......................................................................6
Integrated Circuit Diagrams ...........................................7
Schematic Diagrams .....................................................8
SPECIFICATIONS
Nominal Impedance: . . . . . . . . 4 ohm
Amplifier Power: . . . . . . . . . . . 100W Continuous
Sensitivity: . . . . . . . . . . . . . . . 90 dB SPL*
Crossover Frequency: . . . . . . . 120 Hz (Nominal)
Frequency Response: . . . . . . . 40 Hz to 120 Hz (+/-3 dB)
Amplifier Input Impedance: . . . . 48k ohm(Line)/1k ohm (Speaker)
Aural Sweep Test Specifications:
A. System Aural Sweep Test: . . 5.0V Input, 10 Hz to 1 kHz
B. L.F. Aural Sweep Test: . . . . 5.0V Input, 10 Hz to 1 kHz
External Dimensions
Height . . . . . . . . . . . . . . . . . . 28.17" (716mm)
Width . . . . . . . . . . . . . . . . . . . 10.25" (260mm)
Depth. . . . . . . . . . . . . . . . . . . 12.05" (306mm)
Shipping Weight . . . . . . . . . . . 32 lbs (14.5 kg)
*1 Watt @ 1 Meter
FEATURES
n
The Bass2/Basswave powered subwoofer is part of the
MUSIC 2 System.
n
100 watt output.
n
Variable level control.
n
Line level and speaker level inputs.
n
User friendly auto on circuit. Signal sensing
automatically turns the subwoofer on so you don’t have
to; the subwoofer is meant to be left on without use of
a power switch*
n
Speaker is magnetically shielded for use near televisions
or computer monitors.
* Early versions of the Bass2/Basswave will cycle into a standby mode when the signal source is absent after a
predetermined time; the green LED turns OFF when this happens on the 120 volt version, the LED cycles to RED on
the 230 volt version. The subwoofer’s sensitivity to input signals was increased in later versions and these units stay
ON, even when the input signal is absent. This is a normal condition, and does not compromise the safety, integrity, or
dependability of the product in any way.
2
Powered Subwoofer
BASS2/BASSWAVE
DISASSEMBLY PROCEDURE
To Access Amp. Circuit Boards
1.
Remove (4) base screws; remove base.
2.
Remove (2) large 1/4-20 Torx #30 amp
mounting screws from amplifier bottom.
3.
Remove amp assembly from cabinet; unplug the
(2) output wires.
4.
Remove the (4) Torx #15 screws from top plate.
5.
Remove/scrap adhesive away from the strain
relief plug area in the top cover.
6.
Pry strain relief plug from top cover; remove cover.
To Access Lower Woofer
1.
Remove (4) base screws; remove base.
2.
Remove (2) large 1/4-20 Torx #30 amp mounting
screws from amplifier bottom.
3.
Remove amp assembly from cabinet.
4.
Unplug the (2) wires from woofer; remove the (4)
8 x 3/4 Phillips screws from the inner baffle.
5.
Remove woofer.
NOTES:
1.
The upper woofer is non-serviceable. Order
replacement cabinet/upper driver assy.
(Part # BASSWAVEENCLKIT)
2.
A NEW AMP GASKET, (Part # 75140), between
amp and cabinet is recommended to ensure
airtight seal if the amplifier is removed for any
reason.
3.
If amplifier is serviced for any reason: after the
strain relief plug is inserted back in top cover,
an adhesive, e.g. hot melt glue, silicon seal, epoxy
or similar product must be used on the strain relief
junction to ensure an air tight seal.
PACKAGING EXPLODED VIEW
JBL continually strives to improve its products.
New materials, production methods and design
refinements are introduced into existing models without
notice as a routine expression of our design philosophy.
For this reason, the Bass2/Basswave Subwoofer may
differ in some respect from its published specifications
and descriptions, but will always equal or exceed the
original specifications unless otherwise stated.
3
Powered Subwoofer
BASS2/BASSWAVE
BASS2/BASSWAVE EXPLODED VIEW
Page of 14
Display

Download JBL BASS 2 Service Manual (Repair Manual)

Here you can read online and download JBL BASS 2 Service Manual in PDF. BASS 2 service manual will guide through the process and help you recover, restore, fix, disassemble and repair JBL BASS 2 Audio. Information contained in service manuals typically includes schematics / circuit diagrams, wiring diagrams, block diagrams, printed wiring boards, exploded views, parts list, disassembly / assembly, pcb.