MS 150 (serv.man4) - Harman Kardon Audio Service Manual (repair manual). Page 10

Read Harman Kardon MS 150 (serv.man4) Service Manual online

English
9
To  change  the  EQ  mode,  place  the  MS  150  in  the  Standby  mode.  Then  press  the  Source 
button. The SETTINGS menu appears in the MS 150 Message Display. Press the  button 
to toggle between the ALARM VOLUME and EQ menu options. When EQ is displayed, use 
the  or  button to toggle between TAbLE and WALL. Press the Source button to save 
your selection.
Volume Control
Use the front-panel or remote Volume controls to raise or lower the volume. The default 
setting at turn-on is 12, and the maximum setting is 30. Use caution with volume levels 
to avoid damage to your hearing or equipment. The volume level appears in the Message 
Display when the Volume controls are used.
To silence playback temporarily, press the Mute button on the remote, or simultaneously 
press  the  front-panel  Volume  Up  and  Down  buttons.  “Mute”  will  flash  in  the 
Message  Display.  Press  the  Mute  button  or  either  Volume  control  to  resume  normal  
volume. Source playback will continue during muting.
Source Selection
The  first  time  the  MS  150  is  turned  on,  it  will  default  to  FM  Radio.  Each  press  of 
the  Source  Selector  switches  to  the  next  source  in  this  order:  FM,  CD,  AUX  LINE  IN  1  
(rear-panel 3.5mm analog input), AUX LINE IN 2 (front panel), AUX LINE IN 3 (rear-panel 
dual RCA jacks), AUX DIGITAL IN, iPod/iPhone. 
Subsequently, when you turn the MS 150 on, it will select the last source used before you 
placed it in the Standby mode.
FM Radio
Press the Tuning Mode button to select Automatic or Manual tuning. The AUTO indicator 
appears when Auto tuning is active. 
In Auto tuning mode, pressing the Tuning Up and Down buttons causes the radio to scan in 
the selected direction for a signal with acceptable strength, then stop. The radio will also 
stop if you press one of the Tuning buttons again.
In Manual tuning mode, each press of the Tuning Up and Down buttons causes the radio to 
tune to the next frequency in the selected direction.
If  a  stereo  signal  is  detected,  the  STEREO  indicator  will  light.  Monaural  stations  or  weak 
stereo stations will be played in mono.
To select a preset station, use the Preset Search buttons. 
If the station is broadcasting RDS (Radio Data System) information, the information will be 
displayed. The second line of the Message Display may show the station’s call letters, a name 
or other information, depending on what the station broadcasts. The third line indicates 
the Program Type (PTy) when broadcast. When no RDS information is available, only the 
station’s broadcast frequency will be displayed.
Program Station Presets
To program a preset for quick access to favorite stations, tune to the station’s frequency and 
press and hold the Play/Pause/Memory button for two seconds. The P01 preset will appear. 
If no station has been programmed into the preset, the current station will be stored. 
If a different station was previously programmed, it will be overwritten by the new station. 
To select a new preset, use the Preset Up/Down buttons; six presets are available. If all six 
have been programmed, you must overwrite or erase one to program a new station preset.
If the current station was stored in the preset position, the preset will be erased.
CD
First press the Eject button to ensure that the CD slot is empty. Then gently insert a CD, CD-R, 
CD-RW, enhanced CD, MP3 or WMA disc, label side up, partway into the slot. The loading 
mechanism will detect the disc and pull it the rest of the way in. Do not attempt to force 
the disc. If the disc will not load, turn off the MS 150, unplug it and bring it to an authorized 
harman kardon service center for inspection.
If another source is playing, the MS 150 will not automatically switch to the CD. Press the 
Source Selector button repeatedly until “CD” is selected.
The “Reading” message will appear for a few moments while the MS 150 identifies the disc 
type. The correct indicator will appear in the Message Display.  
In normal operation, the disc will automatically begin playing when you select "CD" as the 
source. The Play icon will appear, along with the current and total track numbers and the 
elapsed track time. When the disc has finished playing, the Stop icon will appear, with the 
total number of tracks and total disc time.
Playback Control
To  pause  playback  momentarily  for  later  resumption  at  the  same  point,  press  the  Play/
Pause/Memory  button.  Press  the  button  again  to  resume  play.  The  Pause  icon  will  be 
displayed. Press and hold the Play/Pause/Memory button for two seconds to stop playback 
fully.   
To  search  at  10x  speed  through  the  current  track,  press  and  hold  the  Skip/Scan 
 
Forward or Skip/Scan Reverse button. When the track’s beginning or end is reached, 
normal play will begin.
To skip to the next track, tap the Skip/Scan Forward button. If the current track is the 
 
last one on the disc, the MS 150 will skip to the first track.
To return to the beginning of the current track, tap the Skip/Scan Reverse button. Tap 
 
it twice quickly to skip backwards to the previous track.
For  repeat  or  random  (shuffle)  play,  press  the  Playback  Mode  button.  Each  press 
 
changes  the  playback  mode  as  follows:  Repeat  1  Track,  Repeat  All  Tracks,  Shuffle, 
Shuffle with Repeat All and Normal Playback.
Data Discs
When an MP3 or WMA disc is loaded, the disc type indicator will light up, and the number 
of folders and tracks in the current folder will be displayed. Play will begin automatically. If 
the disc has both MP3 and WMA tracks, both indicators will light.
For MP3 discs, the track name and artist will alternate in  the display. For WMA discs, the 
album and track number will alternate in the display. 
For both disc types, the Skip, Scan, Repeat and Random play functions are the same as for 
audio CDs.
JPEG discs are not compatible with the MS 150, and the display will indicate that they have 
no files and no folders. 
Auxiliary Inputs
The MS 150 is equipped with three analog audio inputs and one digital audio input. If you 
have  connected  a  compatible  device,  such  as  a  portable  audio  player  or  a  cassette  deck, 
select the corresponding auxiliary input as the source and use the device’s own controls. 
  
AUX LINE IN 1 (Analog): rear-panel 3.5mm jack, shared with Digital Input
  
AUX LINE IN 2 (Analog): front-panel 3.5mm jack
  
AUX LINE IN 3 (Analog): dual rear-panel RCA-type jacks
  
DIGITAL LINE IN: rear-panel 3.5mm jack
MS 150
Operation
 
NOTE: To cancel programming or erasing of a preset, press any other key.
 
NOTE: If the “Error” message appears, the disc is not compatible with the MS 150, 
or its data may be damaged. Press the Eject button to remove it.
0291CSK - HK MS150 OM v6.indd   9
07/06/11   10:41:10
Harman Kardon, JBL
HK MS 150+JBL MX 150/230V Service Manual
Page 10 of 64
Page of 64
Display

Click on the first or last page to see other MS 150 (serv.man4) service manuals if exist.