Read Harman Kardon HS 2X0 (serv.man5) Service Manual online
8
MODEL: HS 2X0SO/230
Speaker
Outputs
Coaxial
Digital
Inputs
Optical
Digital
Inputs
Subwoofer
Output
Coaxial
Digital
Output
AC Power
Input
Sub
Trigger
Output
Line
Outputs
Line 2
Inputs
SCART
Connection
FM
Antenna
Connection
Line 1
Inputs
Ethernet
Port
USB
Port
HDMI
Output
Composite
Video
Output
S-video
Output
Remote Control
Input/Output
Receiver Rear-Panel Connections
See the Connections section, on page 14, for detailed information
about making connections.
AC Power Input: After you have made and confirmed all other
connections, plug the supplied AC power cord into this input and
into an unswitched AC outlet.
Speaker Outputs: Use the speaker wires supplied with the SAT TS60
speakers to connect the satellite speakers to the proper terminals.
Be sure to connect the positive (+, colored red) connector on the
speaker to the positive (+, colored red and white) connector on the
HS 2X0SO/230, and the negative (– , colored black) connectors on the
speakers to the negative (–, colored black) connectors on the
HS 2X0SO/230. See Connecting the Satellite Speakers, on page 14, for
more information about making connections.
Coaxial Digital Inputs: Connect the coaxial digital output of an
audio-only source component here. The signal may be a Dolby Digital
bitstream or a standard PCM digital audio bitstream.
NOTE: Use only one type of digital connection for each source
component.
Optical Digital Inputs: Connect the optical digital output of an
audio-only source component here. The signal may be a Dolby Digital
bitstream or a standard PCM digital audio bitstream.
NOTE: Use only one type of digital connection for each source
component.
Coaxial Digital Output: Connect this output to the coaxial digital input
of a digital recording device such as a CD-R or MiniDisc recorder.
Sub Trigger Output: Use the black mini-cable connector of the
supplied combination LFE and trigger cable to connect this jack to the
HKTS200SUB subwoofer’s External Trigger Input. See Connecting the
Subwoofer, on page15, for more details about making connections.
Whenever the HS 2X0SO/230 is turned on, it will send a trigger signal
that will turn the subwoofer’s amplifier on. Turning the HS 2X0SO/230
off removes the trigger signal, and the subwoofer’s amplifier will turn
off. (This change will occur even when the subwoofer’s Power On Mode
switch – see page 9 – is in the Auto position.)
Subwoofer Output: Use the LFE (purple) connector of the supplied
combination LFE and trigger cable to connect this jack to the
HKTS200SUB subwoofer’s Line-Level In LFE jack. See Connecting
the Subwoofer, on page 15, for more details about making connections.
Ethernet Port: Connect this port to your local area network (LAN) using
a CAT 5 RJ45 network cable. See Connecting to a Local Area Network
(LAN), on page 17, for details.
Line Outputs: Use the Line Outputs to connect to an audio-only re-
corder, such as a CD-R recorder or tape deck.
USB 2.0 Port: Gently insert a flash drive, card reader, digital camera
or other USB device, or a USB Standard-A cable connected to a USB
device, to this port.
IMPORTANT: DO NOT connect a PC or other USB host/controller to this
port, or you may damage both the HS 2X0SO/230 and the other device.
Orient the device’s plug so it fits all the way into the HS 2X0SO/230’s
USB connector. You may insert or remove the device at any time – there
is no installation or ejection procedure.
The HS 2X0SO/230 can display JPEG-format still-image files stored on
the device and can also play MP3 and Windows Media
®
Audio (WMA)
files and MPEG4 and AVI video files that are stored on the device.
Line 1 Input/Line 2 Inputs: Use these inputs to connect to an
audio-only source component (such as a tape deck). Do not connect
a turntable to these jacks without a phono preamp.
HDMI Output (HDMI version 1.2): If your video display is
HDMI-capable, connect it to the HS 2X0SO/230’s HDMI output for im-
proved video performance. Since the HDMI cable transmits both video
and audio to the video display, we recommend that you disable your
display’s HDMI audio function to take full advantage of the
HS 2X0SO/230's system’s superior audio performance.
IMPORTANT: The HS 2X0SO/230 is in compliance with HDCP (High-Def-
inition Copy Protection). A video display must also be HDCP-compliant
to be used with the HS 2X0SO/230’s HDMI output. For best results, we
do not recommend HDMI connections in excess of ten feet without a
repeater. If your video display has a DVI input, you may use an optional
HDMI-to-DVI cable or adapter for the video connection to the display.
(The DVI connection is video-only.)
harman/kardon
HS 2X0/230 Service Manual
Page 6 of 73
Click on the first or last page to see other HS 2X0 (serv.man5) service manuals if exist.