DPR 1005 (serv.man2) - Harman Kardon Audio User Guide / Operation Manual. Page 46

46 PROGRAMMING THE REMOTE

The DPR 1005 remote is factory-programmed for
all functions needed to operate the unit. In addi-
tion, it is also preprogrammed to operate most
recent Harman Kardon DVD players and chang-
ers, CD players and changers, CD recorders and
cassette decks. The codes for other brand devices
may be programmed into the DPR 1005 remote
using its extensive library of remote codes or a
head-to-head learning process for codes not in
the internal library.

Thanks to the remote’s advanced technology and 
two-line LCD display, it is no longer necessary to 
look up cumbersome codes when programming
the remote; following the steps outlined below,
you simply search for the brand name from the
remote’s memory. We recommend that you first
try the preprogrammed code entry method. If
that procedure is not successful, then try the
code learning method.

The easiest way to program the DPR remote for 
operation with a source device from another
brand is to follow these steps:

1. Turn on the power to the device you wish to

program into the DPR remote. This is impor-
tant, as in a later step you will need to see
whether the device turns off to determine
whether the remote has been programmed for
the proper remote codes.

2. Press and hold the Program Button

& for

about three seconds while the message shown 
in Figure 15 appears in the remote’s LCD
Information Display

2. Release the but-

ton when the red light under the Set Button
F appears.

3. The remote’s 

MAIN MENU

message (Figure

16), will appear in the LCD display and the
Set Button

F will remain illuminated in

red. Press the Set Button

F to begin the

process of selecting a device and locating the
proper remote codes.

4.

SELECT A DEVICE

will appear in the LCD

display (Figure 17).
Press the 

⁄¤

E to

scroll through the list of device categories and
press the Set Button

F when the device

you wish to set the codes for appears.

For this example, we will select “TV” to enter the
codes needed to operate your TV.

NOTE: The codes for hard-drive recorder prod-
ucts (PVR) such as TiVo and Replay are pro-
grammed by selecting VCR as the device. For
satellite-based TiVo products, check under the
brand name of the product.

5. At the next menu screen on the remote (Figure

18) press the Set Button

F to enter the

Manual mode, which means that you will
select the brand name of the device from the
list programmed into the remote’s memory.

6. The next menu screen on the remote (Figure

19) will show the start of the list of available
brands. Press the 

⁄¤

E until the brand name of the device you
are programming into the remote appears on
the lower line of the display and then press
the Set Button

F.

NOTE: If the brand name for the product you
wish to program does not appear in the list, the
codes may still be available, as some manufactur-
ers share codes. If the desired brand is not listed,
press the Clear Button

# to exit the pro-

gramming process, and skip to the instructions
shown on page 47 for the “Automatic” method
of programming the remote. If desired, or if the
codes for your brand are not part of the remote’s
library at all, you may still use the DPR remote to
program most infrared-controlled products by
“learning” the commands from the product’s
original remote into the DPR remote. The instruc-
tions for Learning Commands are on page 47.

7. The next step is important, as it determines

which codes will operate the source device or
display. Point the DPR remote at the device
being programmed and, following the instruc-
tions shown in the remote’s LCD
Information Display

2, press and release

the Numeric Keys

H shown on the menu

screen (Figure 20) one at a time, starting with
the “1” button. After you press the “1”
Button

H, the remote’s LCD screen will

briefly go blank as the code is being transmit-
ted, but you will see the “transmit” icon 
in the upper right corner of the display to
serve as confirmation that the remote is
sending out commands.

8. After you press and release the number key,

watch the device being programmed to see
whether it turns off. As shown in the instruc-
tions that will appear on the next menu screen
(Figure 21), if your device has turned off, press
the Set Button

F, and then skip to Step

10. If the unit does not turn off, proceed to the
next step.

9. If the device being programmed into the DPR

remote does not turn off after you have
pressed the “1” key, continue Steps 8 and 9
by pressing the available numeric keys shown
until the device turns off. If the device still
does not turn off after all choices have been
tried, or if there is only one number key
shown as available to try, the code for this
specific device is not in the DPR remote
library under that brand name. If that is the
case, press the Clear Button

# to exit the

manual programming mode. Remember that
the codes may still be stored in the DPR
remote’s library under another brand, and
you can have the remote control search for
them by following the instructions below for
automatic programming. You may also manu-
ally “learn” the codes for most devices into
the DPR remote by following the Learning
Commands instructions on page 47.

10. When the device being programmed does

turn off after a numeric key has been
pressed, you must press the Set Button

F

within five seconds to enter the setting into
the remote’s memory. After you press the Set
button, the top line of the LCD display will
read 

SAVING…

and then the word 

SAVED

will flash four times in the center of the bot-
tom line.

11. When the codes are saved the remote will

return to normal operation, and whenever
you press the Input Selector Button

4

that was just programmed, the codes for the
new device will be used. If no further buttons
are pressed, the remote will revert back to
the default setting for DPR commands.

NOTE: Some brands share a common remote
control code for “Power Off” for many models.
For that reason it is possible that even though
the remote appears to be properly programmed,
you may find that some buttons do not appear to
issue the correct command. If this is the case,
repeat the procedure outlined above, but if more
than one numeric key selection is suggested in
Step 7, try a different number to see whether the
remote operates correctly.

P O W E R   O F F ?   Y : S E T

N :   N E X T

#   O R   C L R

P R E S S   A   N U M B E R

C O D E   1   O F   1 0

S E L E C T   B R A N D

R C A

P R O G R A M   D E V I C E

M A N U A L

S E L E C T   A   D E V I C E

T V

M A I N   M E N U

P R O G R A M   D E V I C E

H O L D   P R O G   B U T T O N

F O R   3   S E C O N D S