DMC 1000 - Harman Kardon Audio Info Sheet (repair manual). Page 13

1

4

5

6

7

8

2

A

9

3

B

D

C

E

F

FROnT PAnEL COnTROLS

IMPORTANT NOTE: The DMC 1000’s front-
panel controls use advanced touch-sensitive 
technology. To use the front panel, place a finger 
over any of the illuminated icons. A gentle tap is 
all that is necessary. Wait a few seconds for the 
DMC 1000 to process each command. To remove 
fingerprints, wipe the front panel with a dry 
microfiber cloth.
Power: When the DMC 1000 is connected to 
an AC power source and the rear-panel Master 
Power Switch is on, this control will indicate one 
of four power states:
•  Full-Off Mode (dim blue) – The DMC 1000, 

including its hard-disc drive, is fully powered 
down.

•  Sleep (Standby) Mode (amber) – The DMC 

1000 will not respond to any commands other 
than to power on.

•  Server Mode (amber) – Server Mode has no 

function.

•  Full-Power Mode (bright blue) – The DMC 

1000 operates normally.

The description of each mode and the DMC 
1000’s response to the power controls is shown 
in Table A7 in the Appendix.

0

 Main Information Display: This  display 

delivers messages and  status indications to help 
you  operate the DMC 1000 player.

1

 Power On/Off (Standby): Press the button 

once to turn the DMC 1000 player on, press it 
again to put the unit in the Standby mode. 

2

 Open/Close: Press this button to open or 

close the Disc Tray.

3

 Disc Drawer.

4

 Play/Pause: Press to initiate playback or to 

resume playback after Pause has been pressed. 
Press this button to momentarily pause playback. 
To resume playback, press the button again. If a 
DVD is playing, action will freeze and a still pic-
ture will be displayed when the button is pressed. 

5

 Stop: Press this button once to place the disc 

in the Resume mode, which means that playback 
will stop, but as long as the tray is not opened 
or the disc changed, DVD playback will continue 
from the same point on the disc when the Play 
Button is pressed again. Resume will also work if 
the unit was turned off. To stop a disc and have 
play start from the beginning, press the button 
twice.

6

 Skip/Search (Previous): Press this button 

to move backward through the music tracks on a 
CD disc or the chapters on a DVD disc. Keep the 
button pressed to search backwards at one of the 
available speeds.

7

 Skip/Search (Next): Press to move forward 

through the music tracks on a CD or the  chapters 
on a DVD disc. Keep the button pressed to search 
forwards at one of the available speeds.

8

 Record: When an audio CD is loaded, or the 

Analog Audio Inputs are selected as the source, 
press this button to view the Record tab of the 
on-screen menu. Pressing this button does not 
begin the recording.
NOTE: It is not possible to record from one of 
the memory cards or the USB device to any other 
media or to the USB device. It is also not pos-
sible to transfer image or video files. However, 
an audio signal is always available at the Analog 
Audio Outputs. You may make analog recordings 
from any source by connecting an analog audio 
recorder to the rear-panel Analog Audio Outputs.

9 

Menu:  Press to activate the on-screen 

menu system, or to navigate back up one level in 
the menu system.
NOTE: It is not possible to select a new source 
while the current source is playing or even while 
it is paused. Press the Stop Button before select-
ing a new source.

0

 Ecran d’information principal

1

 Marche/Arrêt (Mode de veille)

2

 Ouverture du plateau

3

 Tiroir de disque

4

 Lecture/Pause

5

 Arrêt

6

 Saut/Recherche (Amont)

7

 Saut/Recherche (Aval)

8

 Enregistrer

9

 Menu

A

 Touches de navigation

B

 Porte du panneau avant 

C

 Fente à carte 1

D

 Fente à carte 2

E

 Port USB

F

 Capteur IR de télécommande