DIGITAL LOUNGE (serv.man2) - Harman Kardon Audio User Guide / Operation Manual. Page 19

INSTALLATION AND CONNECTIONS

Notes
• The Power Requirement is: AC 230V, 50 Hz.

• Connecting to power other than the one listed

above may damage the system or cause abnor-
mal operation.

• Before connecting the AC power cord of this

system to a wall outlet, connect the speakers
and other component cables to the system.

• Connect the AC power cord of the active

subwoofer.

• Connect the AC power cords of your TV and

any optional components to a wall outlet.

Once the speakers have been placed in the room
and connected, the remaining steps are to
program the system configuration memories.

You are now ready to power up the system to
begin final adjustments.

1. Plug the Power Cable

4Q of the DVD

receiver and TV into an unswitched AC outlet.
Press the Power On Switch 

G to the "I" 

position to switch on the TV to Standby mode.
Note that the Power Indicator

1 and the

Power Indicator on the screen will turn orange,
indicating that system unit is in the Standby
mode. At the same time, plug the power cord of
the subwoofer into an unswitched AC outlet.

2. Remove the protective plastic film from the

main front-panel lens of the DVD receiver.
If left in place, the film may affect the perform-
ance of your remote control.

3. Install the three supplied AAA batteries in the

main remote as shown. Be certain to follow
the (+) and (–) polarity indicators that are on
the top of the battery compartment. Follow the
same instructions to install the three supplied
AAA batteries into the smaller second remote
control.

4. Turn the system on by pressing the TV Input

0 on the remote control.

The Power Indicator

1 and the Power

Indicator of the screen will turn blue to confirm
that the system is on, and the Main
Information Display

 will also light up.

The first step after switching on your system is to
set the language you prefer and the country you
reside in. Once that is done, the automatic TV
channel search will start.

• The first screen you will see is the Language

Selection screen. Use the [

L

] or [

K

] Buttons

9 to select the language you prefer to see
the menu's of the TV in. Press the Enter Button
6 to confirm.

• Once you have selected the menu language,

the next screen allows you to select the country
in which the TV will be operated. Use the [

L

]

or [

K

] Buttons 

9 to select your country.

When you press the Enter Button 

6 to con-

firm, the automatic channel search will start to
scan the available TV channels. The automatic
search can take several minutes, depending on
the number of channels that are available.

• Should you wish to abort the automatic 

channel search, please press the Red Button
N on your remote control.

If no TV channel is found, check the aerial con-
nections and attempt to search for the channels
again.

When the automatic search is finished, the Edit
Channel List Menu will show on your screen. It
will show all the TV channels found indicated by
a name consisting a maximum of 5 characters.
This menu allows you to sort the TV channels
according to your preferences. Move the blue bar
by pressing the 

L

Button until the TV channel

you would like to move is highlighted by the blue
bar. Press the Enter Button 

6 so that the bar

turns white. You can now move it up, down, left
or right with the 

K

/

L

/

M

/

N

Buttons 

9 until it

is at the requested preset. Press the Enter Button
6 to confirm. The white bar will turn blue to
confirm. Continue with all the other channels
until each preset contains your preferred TV chan-
nel.

The menu also allows you to delete TV channels
from your channel list. Move the blue bar to the
TV channel to be deleted using the 

K

/

L

Buttons 

9. Press the Green Button O to

delete the TV channel.

When you are done making changes to the
Channel List, press the Red Button 

N to

remove the list from the screen.

Preparation
1. Depending on what source you would like to

watch or listen to, there are two ways to
switch on the system. In order to switch on the
whole system, including the screen, to watch a
source, press any of System On/Source
Selectors 

0. If you would only like to switch

on the DVD receiver, for instance to simply lis-
ten to a CD, press any of the Audio System
On/Source Selector Buttons 

K.

2. When you switch on the complete system, a

Harman Kardon Digital Lounge welcome
image should appear on the screen.

3. If there is no picture at all, not even the

Harman Kardon screen, please check whether
the HDMI cable has been inserted correctly.
This cable needs always to be connected
before switching on the screen and the receiver.