CDR 2 (serv.man21) - Harman Kardon Audio User Guide / Operation Manual. Page 9

REAR-PANEL CONNECTIONS  9

¡ Play (CDP)-Deck Analog Output: These
jacks carry the analog audio output signal from
the Play Deck 3 during playback, in Single
mode also from the Record Deck %, and dur-
ing CD Dubbing. Connect them to the CD input
jacks on a receiver, preamp or processor.

™ Record (CDR)-Deck Analog Output:
These jacks carry the output signal from the
Record Deck % during playback, in Single
mode also from the Play Deck 3, and during
analog or digital recording. Connect them to the
Tape Play/In input jacks on a receiver, preamp
or processor.

£ Record (CDR)-Deck Analog Input: These
jacks accept the analog signals that are used for
CD recordings. Connect them to the Tape Rec
outputs on a receiver, preamp or processor.

¢ Play (CDP)-Deck Coaxial-Digital
Output: This jack carries the digital-audio out-
put signal from the Play Deck 3 during play-
back, in Single mode also from the Record
Deck %, and during CD Dubbing. Connect it to
a coaxial-digital input on a receiver, processor or
digital decoder.

∞ Record (CDR)-Deck Coaxial-Digital
Output: This jack carries the digital audio out-
put signal from the Record Deck % during
playback and during digital recordings, in Single
mode also from the Play Deck 3 during play.
Connect it to a coaxial digital input on a receiv-
er, processor or digital decoder.

§ Record (CDR)-Deck Coaxial-Digital
Input: This jack accepts the digital-audio input
signal from a compatible digital audio product
and should be connected to a coaxial-digital
output on a CD, MD or DVD player or an A/V
receiver or processor.

IMPORTANT NOTE: The coaxial digital outputs
and inputs should only be connected to digital
input or output jacks. Even though they use the
same RCA type connector as standard analog
audio connections, DO NOT connect them to
conventional analog input or output jacks.

¶ Record (CDR)-Deck Optical-Digital
Input: This jack accepts the digital-audio input
signal from a compatible digital audio product,
and should be connected directly to the optical-
digital output on a CD, MD or DVD player or an
A/V receiver or processor.

• Record (CDR)-Deck Optical-Digital
Output: This jack carries the digital audio out-
put signal from the Record Deck % in Single
mode also from the Play Deck 3 during play.
Connect it to an optical digital input on a receiv-
er, processor or digital decoder.

ª Play (CDP)-Deck Optical-Digital
Output: This jack carries the digital audio out-
put signal from the Play Deck 3 during play-
back, in Single mode also from the Record
Deck %, and during CD Dubbing. Connect it to
an optical-digital input on a receiver, processor
or digital decoder.

‚ Remote IR Input: Connect the output of a
remote infrared sensor or the remote control
output of another compatible Harman Kardon
product to this jack. This will enable the remote
control to operate even when the front-panel
Remote Sensor Û is blocked. This jack may
also be used with compatible IR remote control
based automation systems.

⁄ Remote IR Output: Connect this jack to
the IR input jack of another compatible Harman
Kardon remote controlled product to have the
built-in remote sensor Û on the CDR 2 provide
IR signals to other compatible products.

¤ AC Power Cord: Connect this plug to an
AC outlet. If the outlet is switch controlled, make
certain that it is in the ON position.

¡ Play (CDP)-Deck Analog Output
™ Record (CDR)-Deck Analog Output
£ Record (CDR)-Deck Analog Input
¢ Play (CDP)-Deck Coaxial-Digital Output

∞ Record (CDR)-Deck Coaxial-Digital Output
§ Record (CDR)-Deck Coaxial-Digital Input
¶ Record (CDR)-Deck Optical-Digital Input
• Record (CDR)-Deck Optical-Digital Output

ª Play (CDP)-Deck Optical-DIgital Output
‚ Remote IR Input
⁄ Remote IR Output 
¤ AC Power Cord