AVR 85 (serv.man4) - Harman Kardon Audio User Guide / Operation Manual. Page 19

Read Harman Kardon AVR 85 (serv.man4) User Guide / Operation Manual online

Remote Control Programming and Operation
All other keys may only be programmed
with one remote code. The code
contained in these keys remains the
same regardless of the source selection.
WARNING: These keys transmit codes
that are vital to the operation of the
product. It is not recommended that they
be programmed with alternative codes,
as it may then be impossible to operate
certain functions of the receiver.
Night 
Delay
RF 
Opt
Coax
Select 
All Navigation Buttons ‹ ›
⁄¤
All Mode Selectors
*
#
Display
OSD 
Speaker 
⁄¤
CH Select
Volume 
⁄¤
Test Tone
Mute
To program the remote, follow these steps.
Note that it is not necessary to program
all keys, only those that are required to
operate the subject device. Keys not pro-
grammed will retain the codes prepro-
grammed at the factory.
1. Slide 
Use/Learn
a
switch at the
top left corner of the remote to the right
so that it is next to 
Learn
.
2. If one of the multifunction buttons 
is being programmed press the source
button (i.e. 
CD
VID 1
, etc.) you wish to
have this function associated with. If you
are programming a single function key,
proceed to the next step.
3. Press the button on the remote that is
to be programmed. Note that the
Learning
`
LED will illuminate.
4. Place the remote head to head with the
remote control whose function is being
learned. The two remotes should be no
more than 8 inches apart.
5. Press and hold the button on the
remote corresponding to the function 
to be memorized until the 
Learning
LED starts to blink. When the LED goes
out, release the button on the transmit-
ting remote. The function code has been
successfully captured by the remote.
NOTE: If both LEDs flash during a pro-
gramming operation, it indicates that
the remote’s memory is full or that the
remote codes from the transmitting
remote are not compatible with the unit’s
signal format.
6. Continue to program any additional
remote commands required using steps
2 through 5. When you have finished
programming the remote, slide the
Use/Learn
switch to the left so that it
is in the
Use
position.
Clearing the Remote Memory
In normal operation, codes for a new
device may be programmed “over” the
codes that have been previously pro-
grammed into the remote. It is also pos-
sible to clear the memory for individual
keys, or for the entire remote. When a
memory position is cleared, the remote
will return to the original factory preset
command.
To clear the memory for a specific indi-
vidual key location, put the 
Use/Learn
switch in the 
Learn
position. Press the
Main Power Off
c
button and the
button to be cleared at the same time.
Both the 
Sending
and 
Learning
indi-
cators will light momentarily. When the
lights go out, the memory has been
cleared of the user programmed code
and returned to the factory preset. Return
the 
Use/Learn
a
switch to the 
Use
position when you are finished. 
To clear the remote’s entire memory 
and return all keys to their factory preset
commands first put the 
Use/Learn
a
switch in the 
Learn
position. Then press
the 
Main Power On
button 
c
and
confirm that the 
Learning
indicator
`
has illuminated. While continuing
to press the 
Power On
button, press and
hold the 
Power Off
c
button until the
Learn
indicator goes off for about 3 sec-
onds. It will then blink twice. Then
release the two buttons. This indicates
that the memory has been cleared of any
user programmed commands and that
the original commands have been
restored. Slide the 
Use/Learn
switch
a
back to the 
Use 
position to return
the remote to normal operation.
16
AVR85 120   rev (g) 6/14/97
AVR85 om (g)  9/16/98 11:21 AM  Page 16
Page of 40
Display

Click on the first or last page to see other AVR 85 (serv.man4) service manuals if exist.