AVR 7000 (serv.man7) - Harman Kardon Audio User Guide / Operation Manual. Page 13

MAIN REMOTE CONTROL FUNCTIONS 13

L Clear/M 4 Button: This button has no
function with the AVR7000, but it controls the
"+10" or "Clear" function with CD or DVD
players (see function list page 42); it may also be
programmed for use with other devices (See
page 38 for more information).

M Preset Up/Down: When the tuner is in
use, press these buttons to scroll through the
stations programmed into the AVR 7000’s mem-
ory. When some source devices, such as CD play-
ers, VCRs and DVD players, are selected using
the Device Control Selectors

2#, these

buttons may function as chapter step or track
advance.

N Tuning Up/Down: When the tuner is in use,
these buttons will tune up or down through the
selected frequency band. If the Tuner Mode but-
ton 

E has been pressed or the Band button

@

on the front panel was held pressed so that

the AUTO indicator V is illuminated, pressing
either of the buttons will cause the tuner to seek
the next station with acceptable signal strength
for quality reception. When the AUTO indicator
V

is NOT illuminated, pressing these buttons will

tune stations in single-step increments. (See page
31 for more information.)

O Forward/Reverse Transport Buttons:
These buttons do not have any functions for the
AVR, but they may be programmed for the for-
ward/reverse play operation of a wide variety of
CD or DVD players, and audio or video- cassette
recorders. (See page 38 for more information on
programming the remote.)

P Night Mode: Press this button to activate
the Night mode. This mode is available in spe-
cially encoded digital sources, and it preserves
dialog (center channel) intelligibilty at low vol-
ume levels (See page 31 for more information).

Q Multi-Room: Press this button to activate
the Multiroom system or to begin the process of
changing the input or volume level for the sec-
ond zone. (See page 37 for more information on
the Multiroom system.)

 Delay/Prev Ch.: Press this button to begin
the process for setting the delay times used by
the AVR 7000 when processing surround sound.
After pressing this button, the delay times are
entered by pressing the Set button 

8 and

then using the 

⁄

/

¤

buttons 

6 to change the

setting. Press the Set button again to complete
the process. (See page 24 for more information.)

›

Button: Press this button to change a set-

ting or selection when configuring many of the
AVR’s settings.

 Speaker Select: Press this button to
begin the process of configuring the AVR
7000’s Bass Management System for use with
the type of speakers used in your system. Once
the button has been pressed, use the 

⁄

/

¤

but-

tons 

6 to select the channel you wish to set

up. Press the Set button 

8 and then select

the speaker type (see page 23 for more infor-
mation.)

  Surround Mode Selector: Press this
button to begin the process of changing
the surround mode. After the button has
been pressed, use the 

⁄

/

¤

buttons 

6 to

select the desired surround mode (See page 28
for more information). Note that this button is
also used to tune channels when the TV, VCR,
AUX and SAT receiver is selected using the
Device Control Selector

#. When the AVR

7000 remote is being programmed for the codes
of another device, this button is also used in the
“Auto Search” process. (See page 38 for more
information on programming the remote.)

!Volume Up/Down: Press these buttons to
raise or lower the system volume.

" Sleep Button: Press this button to place
the unit in the Sleep mode. After the time shown
in the display, the AVR 7000 will automatically
go into the Standby mode. Each press of the
button changes the time until turn-off in the fol-
lowing order:

Hold the button pressed for two seconds to turn
off the Sleep mode setting.
Note that this button is also used to change
channels on your TV, VCR, AUX and SAT receiver
when selected using the Video Remote Selec-
tors

#.

When the AVR 7000 remote is being programmed
for the codes of another device, this button is also
used in the “Auto Search” process (See page 38
for more information on programming the
remote.)

# Video Remote Selectors: Press one of
these buttons to use the remote to control the
functions of the device shown on the button. (For
more information on programming the remote to
operate these devices, see page 38.)

$ IR Transmitter Window: Point this window
towards the AVR 7000 when pressing buttons on
the remote to make certain that infrared com-
mands are properly received.

% RDS Button: When an FM RDS station is
tuned, press this button to select the RDS service
indicated in the display (See page 32 for more
information on RDS).

NOTE: As any of the remote buttons pressed is
active with the device selected, the correspon-
ding Selector button 

12# will briefly

flash red to confirm your selection.

90

min

80

min

70

min

60

min

50

min

40

min

30

min

20

min

10

min

OFF