Read Harman Kardon AVR 660 (serv.man3) Service Manual online
7
USB
ENGLISH
FRONT-PANEL CONTROLS
Power indicator
Standby/On
Switch
Info
Settings
Main
Power
Switch
AVR
Settings
Resolution
Video
Modes
Source
List
OK
USB Port Digital Audio
Inputs
(Optical and
Coaxial Front)
Video Inputs
(S- and Composite
Front)
EzSet/EQ II
Microphone
Input
Back/Exit
Audio
Effects
Surround
Modes
Menu
Analog Audio
Front Inputs
Headphone
Jack
KLM N
Navigation
Remote IR Sensor
Message Display
Volume
Power Indicator: This LED has three possible modes:
Main Power Off
•
: When the AVR is unplugged or the Main Power
Switch is off, this LED is off.
Standby
Standby
•
: Amber indicates that the AVR is ready to be turned on.
On
•
: When the AVR is turned on, this LED turns white.
NOTE: If the PROTECT message ever appears, turn off the AVR and unplug
it. Check all speaker wires for a possible short. If none is found, bring the
unit to an authorized Harman Kardon service center for inspection and
repair before using it again.
it. Check all speaker wires for a possible short. If none is found, bring the
unit to an authorized Harman Kardon service center for inspection and
repair before using it again.
Standby/On Switch: This electrical switch turns the receiver on, or places
it in Standby mode for quick turn-on.
Front-Panel Door (not shown): Most of the controls and connectors
described below are hidden behind this door. To open it, gently grab the right
or left edge of the door and pull it forward and down.
Main Power Switch: This mechanical switch turns the power supply on
or off. It is usually left on, and cannot be turned on or off using the remote
control.
AVR Settings Button: Press this button to access the AVR’s main menu.
Info Settings Button: Press this button to directly access the AVR’s
Source Info submenu, which contains the settings for the current source.
it in Standby mode for quick turn-on.
Front-Panel Door (not shown): Most of the controls and connectors
described below are hidden behind this door. To open it, gently grab the right
or left edge of the door and pull it forward and down.
Main Power Switch: This mechanical switch turns the power supply on
or off. It is usually left on, and cannot be turned on or off using the remote
control.
AVR Settings Button: Press this button to access the AVR’s main menu.
Info Settings Button: Press this button to directly access the AVR’s
Source Info submenu, which contains the settings for the current source.
Resolution: Press this button to access the AVR’s video output resolution
setting: 480i, 480p, 576i, 720p, 1080i or 1080p.
setting: 480i, 480p, 576i, 720p, 1080i or 1080p.
IMPORTANT NOTE: If the AVR’s video output resolution is set higher
than the capabilities of the actual connection, you will not see a picture.
If the best available video connection from the AVR to the TV is either
composite or S-video, press this button and change the resolution to 576i.
than the capabilities of the actual connection, you will not see a picture.
If the best available video connection from the AVR to the TV is either
composite or S-video, press this button and change the resolution to 576i.
Audio Effects: Press this button to directly access the Audio Effects
submenu, which allows adjustment of the tone and other audio controls. See
the Initial Setup section for more information.
Video Modes: Press this button for direct access to the Video Modes
submenu, which contains settings that may be used to improve the picture, if
necessary, after you have adjusted the picture settings using the video display
or TV.
Surround Modes: Press this button to select a surround sound (e.g.,
multichannel) mode. The Surround Modes menu will appear on screen,
and the menu line will appear in the front-panel display. See the Advanced
Functions section for more information on surround modes.
Source List: Press this button to select a source device, which is a
component where a playback signal originates, e.g., DVD.
Menu Button: Press to display the menus for the tuner, the USB device,
The Bridge II, the Network or Internet Radio, when any of those sources is in
use.
Back/Exit: Press this button to return to the previous menu, or to exit the
menu system.
submenu, which allows adjustment of the tone and other audio controls. See
the Initial Setup section for more information.
Video Modes: Press this button for direct access to the Video Modes
submenu, which contains settings that may be used to improve the picture, if
necessary, after you have adjusted the picture settings using the video display
or TV.
Surround Modes: Press this button to select a surround sound (e.g.,
multichannel) mode. The Surround Modes menu will appear on screen,
and the menu line will appear in the front-panel display. See the Advanced
Functions section for more information on surround modes.
Source List: Press this button to select a source device, which is a
component where a playback signal originates, e.g., DVD.
Menu Button: Press to display the menus for the tuner, the USB device,
The Bridge II, the Network or Internet Radio, when any of those sources is in
use.
Back/Exit: Press this button to return to the previous menu, or to exit the
menu system.
Harman Kardon
Page 8 of 264
Click on the first or last page to see other AVR 660 (serv.man3) service manuals if exist.