AVR 35 (serv.man4) - Harman Kardon Audio User Guide / Operation Manual. Page 7

Front Panel Controls

5

1

Press 

this button to apply power to the
AVR35RDS. When the switch is
pressed in the unit is placed in a
Standby mode, as indicated by the
amber LED 

3 surrounding the

control 

2. This button

MUST be pressed in to operate the
unit. To turn the unit completely off
and prevent the use of the remote
control, this switch should be pressed
until it pops out from the front panel so
that the word “OFF” may be read at
the top of the switch.

NOTE:

In normal operation this

switch is left in the “ON” position.

2

When

the 

1 is “ON,”

press this button to turn on the
AVR35RDS; press it again to turn 
the unit off (to Standby mode). Note
that the 

3

surrounding the switch will turn green
when the unit is on.

3

This LED will

illuminate in amber when the unit is in
the Standby mode to signal that the
unit is ready to be turned on. When
the unit is in operation, the indicator
will turn green.

4

This jack may

be used to listen to the AVR35RDS’s
output through a pair of headphones.
Be certain that the headphones have
a standard 6,3 mm stereo phone
plug.

5

Turn this control to

modify the low-frequency output of
the left/right channels by as much as
±10dB. Set this control to a suitable
position for your taste and room
acoustics.

6

Turn this control

to modify the high-frequency output
of the left/right channels by as much
as ±10dB. Set this control to a
suitable position for your taste and
room acoustics.

7

Turn this control

to change the relative volume for the
front left/right channels.

NOTE:i

For proper operation of the

surround modes this control should
be at the midpoint, or “12 o’clock”
position.

8

These

audio/video inputs may be used for
temporary connectiion of video
games, camcorders, digital still
cameras or portable audio products.
To select a source connected to
these jacks, press the 

@.

9

Press this button

to select the device connected to the

jacks a as the

listening source. The previously
selected source will continue to show
in the 

33, and

the red LED above the button will
illuminate to remind you that you are
listening to the tape monitor output
(see page 29).

)

Press this button to select the

device connected to the 

jacks ∞ as the listening source.

!

Press this button to

select the device connected to the

jacks § as the listening

and viewing source.

@

Press one

of these buttons to select a source
connected to the rear panel

inputs £ ›, or the

front panel 

input 

8.

#

Press this button to

select the tuner as the AVR35RDS’s
input source. When it is first pressed
the last station tuned will be heard.
Press it again to change between AM
and FM bands or hold it pressed for
minimum 1 sec to change between
automatic and manual tuning mode
(see page 27 for more information).

$

Press this button to

place the unit in the Sleep mode.
After the time shown in the display,
the AVR35RDS will automatically go
into the Standby mode. Each press
of the button changes the time until
turn-off in the following order:

%

Press the left 

side of the button to tune lower
frequency stations and the right side
of the button to tune higher frequency
stations. When a station with a strong
signal is tuned, the TUNED indicator
R will illuminate in the 

33. Pressing the button will

automatically tune to the next station
with a signal strong enough for
acceptable reseption or it will
manually tune to the next frequency
increment, depending on the tuning
mode selected (see page 27 for
more information).

^

Press this button 

to automatically scan through the
stations that have been programmed
in the AVR35RDS’s memory. The
tuner will play five seconds of each
station before moving to the next
preset station. To stop the scan when
the desired station is heard, press
the button again. (See page 27 for
more information on the tuner
memory system.)