Read Harman Kardon AVR 265 (serv.man5) Service Manual online
Harman Kardon
Service Manual
AVR 265/230
7.1 CHANNEL A/V RECEIVER
Released EU2011
Harman Consumer Group, Inc.
Rev 0, 10/2011
8500 Balboa Boulevard
Northridge, California 91329
CONTENTS
DISASSEMBLY
23
EXPLODED VIEW AND PARTS
24
ELECTRICAL PARTS LIST
25
IC PINOUTS
63
PCB DRAWINGS
130
BLOCK DIAGRAMS
148
WIRING DIAGRAM
150
AMP BIAS ADJUSTMENT
151
SCHEMATIC DIAGRAMS
152-168
ESD WARNING
2
FRONT AND REAR PANELS
4
REMOTE CONTROLS
8
SETTINGS LOCK
12
UPDATING NETWORK SOFTWARE
13
RESET REMOTE AND PROCESSOR
14
TROUBLESHOOTING GUIDE
15
BASIC SPECIFICATIONS
16
APPENDIX, SETTINGS
17
PACKAGE LISTS AND PARTS
22
Harman Kardon
AVR 265/230V Service Manual
Page 1 of 168
Each precaution in this manual should be followed during servicing.
Components identified with the IEC symbol
in the parts list are special significance to safety. When replacing a component identified with
, use only the replacement parts designated, or parts with the same ratings or resistance, wattage, or voltage that are designated in the
parts list in this manual. Leakage-current or resistance measurements must be made to determine that exposed parts are acceptably
insulated from the supply circuit before retuming the product to the customer.
Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are called
Electrostatically Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field effect transistors and
semiconductor "chip" components.
The following techniques should be used to help reduce the incidence of component damage caused by static electricity.
1. Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off any electrostatic charge on
your body by touching a known earth ground. Alternatively, obtain and wear a commercially available discharging wrist strap device,
which should be removed for potential shock reasons prior to applying power to the unit under test.
2. After removing an electrical assembly equipped with ES devices, place the assembly on a conductive surface such as aluminum foil, to
prevent electrostatic charge build-up or exposure of the assembly.
3. Use only a grounded-tip soldering iron to solder or unsolder ES devices.
4. Use only an anti-static solder removal device. Some solder removal devices not classified as "anti-static" can generate electrical charges
sufficient to damage ES devices.
5. Do not use freon-propelled chemicals. These can generate electrical change sufficient to damage ES devices.
6. Do not remove a replacement ES device from its protective package until immediately before you are ready to install it. (Most replacement
ES devices are packaged with leads electrically shorted together by conductive foam, aluminum foil or comparable conductive material.)
7. Immediately before removing the protective material from the leads of a replacement ES device, touch the protective material to the
chassis or circuit assembly into which the device will be installed.
Be sure no power is applied to the chassis or circuit, and observe all other safety precautions.
8. Minimize bodily motions when handling unpackaged replacement ES devices. (Otherwise harmless motion such as the brushing together
or your clothes fabric or the lifting of your foot from a carpeted floor can generate static electricity sufficient to damage an ES devices.
CAUTION :
Harman Kardon
AVR 265/230V Service Manual
Page 2 of 168
AVR 3650, AVR 365
AVR 2650, AVR 265
Audio/video receiver
Owner’s Manual
EN
GL
ISH
0295CSK - HK (x65Series) AVR3650_365_2650_265 CORE OM, WORK18 danny.indd 1
01/07/11 11:33:28
Harman Kardon
AVR 265/230V Service Manual
Page 3 of 168
AVR
4
Front-Panel Controls
Front-Panel Controls
Continued on next page
power
Indicator
message
display
volume
knob
video
modes
button
Setup
button
Ir
Sensor
power
button
left/right
buttons
headphone Jack/
ezSet/eq
mic Input
back/exit
button
resolution
button
Audio
effects
button
Surround
modes
button
up/down
buttons
uSb
port
ok
button
hdmI
®
front
Input connector
Info
button
Source list
button
Harman Kardon
AVR 265/230V Service Manual
Page 4 of 168